Manual Functions; Other Functions; What To Do If Your Appliance Does Not Work - TEFAL BL83SD Manual

MANUAL FUNCTIONS:

Pulse: Press the pulse button to
•
let the appliance run for only a
few seconds at a time. To stop
it, release the button. Press the
pulse button as often as it is necessary.
The longest working time can not be
more than 3 minutes.
Blend: select blend program on
•
screen then choose the speed
setting with + and – buttons,
validate with Start/Stop button.
Then choose timer, default time 2 min and
adjut with + and – buttons, validate with
Start/Stop button the programm will start
immediatly. At the end of the program,
the appliance bips 5 times.
Heat : allows to freely control
•
the way you want to heat.
Press the heat button, the
screen indicates « 75° » but you
can choose the heating temperature
from 40° up to 100° by selecting + and –
buttons. Then press Start/Stop button.
You can set up the working time by
selecting + and - buttons between 5
minutes and 90 minutes, the screen
indicate default time : 10 minutes. Then,
press Start/Stop button.
The remaining time appears on the
screen. Wait for the blender to stop
automatically. The appliance beeps 5
times. You can also stop the blending
during the cycle :
- within 1 minute of working, press the
start/stop button
CLEANING
• Clean the jug immediately after use.
• For easy cleaning, you can use.
Deep clean: Put 800ml of water in
the jug. Select the cleaning program
on the screen and press Start/Stop
button Wait for the end of program.
Finish cleaning the jug with the help of
a sponge.
• Rinse the inside of the jug and the lid
under running water.
• Rinse the inside of the jug and the lid
under running water.
• In the event of the heated part of
the jug getting extremely dirty, fill
in the jar with a mix of water and
washing up liquid and let it soaked
for a few hours to help get it clean.
- more than 1 minute of working, press and
hold the start/stop button for 3 seconds.
Steam*: Add the ingredients in
•
the steam basket. Add 500ml of
water in the jar. Then add the
steam basket in the jar and
close the lid. Maintains heat /steam button
for 2 seconds. The pictogram will become
yellow You can set up the working time by
+ and -buttons, between 5 minutes and 90
minutes. Then press Start/Stop button. The
remaining time appears on the screen.
Wait for the blender to stop automatically,
The appliance bips 5 times. For safety
reasons, remove the cap and wait
1 minute to remove excess steam.
*Depending on model

OTHER FUNCTIONS

Start/Stop : allows to stop any
•
blending or heating program
before the end by pressing this
button.You can also stop the
blending during the cycle :
- within 1 minute of working, press the
start/stop button
- more than 1 minute of working, press
and hold the start/stop button for 3 seconds
If the appliance switches off during
operation, proceed as follows :
- Unplug and leave it to cool down for
approximately 15-20 minutes.
- Reconnect the appliance to the power
supply and resume blending.
- The appliance will keep the program in
memory for 3min if stopped.
• Use a damp cloth to clean the
motor Unit. Dry it carefully.
• You can use the brush to clean the
blade holder. Be careful, the blades
are very sharpened.
Caution:
• Empty the preparation, the jug is
not meant for storing food in the
refrigerator or freezer.
• To clean the outside of the motor
unit and the walls of the jug, use a
damp cloth.
• Do not immerse the appliance in
water (neither the motor unit nor
the blade holder). Never put the
motor unit (E) under running water.
• Refer to the cleaning table to
check how to clean each part.
22

WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK ?

Problems
The plug is not connected.
The blender jug is not
positioned correctly on the
motor unit or the jug and lid
are correctly in place and are
Appliance does not
not locked onto the motor unit.
work
Appliance, keypboard or
program not responding
In case of overheating
The appliance stopped
Overload or overheating
while in use
The product is not placed on a
flat surface.
Excessive vibrations
Volume of ingredients is too
high.
Volume of ingredients is too
high.
The lid is not correctly
Leak or overflow from
positioned.
the lid
The seal of the lid is not
correctly positionned, or is
missed.
Deterioration of the
Leak from the bottom of
watertightness of the
the blender jug
appliance.
Causes Solutions
Connect the appliance to a
socket with the same voltage
as indicated on the rating
plate of the appliance.
Check that the blender jug
and the lid are positioned
properly on the motor unit as
explained in the instructions.
Unplug the appliance, wait for
1 minute and plug in again.
Unplug and leave it to cool
down for approx.15-20 minutes.
Unplug and leave it to cool
down for approx.15-20 minutes.
Reconnect the appliance to
the power supply and resume
blending.
Place the appliance on a flat
surface.
Reduce the quantity of
ingredients processed.
Reduce the quantity of
ingredients processed.
Place the lid correctly on the
blender jug.
Put the seal in the correct
position.
verify the blade holder is
correctly put in place and
the interface between blade
holder / jug is totally clean.
If the problem persists, contact
the consumer service (see
contact information in the
warranty leaflet)
23
EN