Page 1
DS-LEDIER Series Compatible with Samsung IER, IFR and IEA series displays *Actual configuration may vary ENG Installation video for reference only. Read and follow instruction manual for full installation. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 2
WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. This product is designed to be installed on flat, unobstructed, vertical walls. Do not install on curved or angled walls. Before installing make sure the supporting surface will support the combined load of the equipment and hardware.
Page 3
Tools Needed for Assembly. ENG To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws. 5/32" (4mm) +1/2 3/8" (10mm) 2.5mm 2020-07-01 #:146-9053-7 (2022-12-22)
Parts (Before beginning, make sure you have all parts shown below). Refer to parts list included with your model. Parts List left column right column inside column vertical spacer Description A left column B right column C inside column D vertical spacer E horizontal spacer F top left horizontal extrusion G top right horizontal extrusion...
Page 5
top left horizontal extrusion top right horizontal extrusion bottom left horizontal extrusion bottom right horizontal extrusion top horizontal extrusion bottom horizontal extrusion 2020-07-01 #:146-9053-7 (2022-12-22)
Page 6
Optional: If connecting two top horizontal extrusions, first remove inner hook-on brackets. Remove and save hardware. Use extrusion connectors to connect top horizontal 2.5mm extrusions. J (4) M (8) 2020-07-01 #:146-9053-7 (2022-12-22)
Page 7
Replace one hook-on bracket in between connected extrusions. Use saved hardware. Optional: If connecting two bottom horizontal extrusions, first remove inner hook-on brackets. Remove and save hardware. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 8
Use extrusion connectors to connect bottom 2.5mm horizontal extrusions. J (3) M (6) Replace one hook-on bracket in between connected extrusions. Use saved hardware. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 9
This page intentionally left blank. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 10
WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8"...
Page 11
Level top horizontal extrusion and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick). 2020-07-01 #:146-9053-7 (2022-12-22)
Page 12
1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). Level extrusion. Install using wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.). 2020-07-01 #:146-9053-7 (2022-12-22)
Page 13
Edges must be flush. Secure vertical spacers to the wall flush with the horizontal extrusion. 0.27" (6.9mm) 3/8" (10mm) 2020-07-01 #:146-9053-7 (2022-12-22)
Page 14
Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick). Edges must be flush. 0.27" (6.9mm) 2020-07-01 #:146-9053-7 (2022-12-22)
Page 15
1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then install using wood screws 3/8" provided. (10mm) Maximum 80 in. • lb (9 N.M.). 2020-07-01 #:146-9053-7 (2022-12-22)
Page 17
Hook on and secure outer vertical columns. "L" and "R" markings designate left and right Tighten hardware. column. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 18
Hook on and secure all inside vertical columns. Tighten hardware. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 19
Loosen hardware on vertical columns. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 20
Plumb and level outer columns, then tighten hardware. Tighten hardware on four corner wall plates. Tighten. Tighten. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 21
Tie a string between top slots on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. Optional leveling for bowed walls. Loosen. Insert. Tighten. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 22
Tie a string between bottom slots on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. Optional leveling for bowed walls. Loosen. Insert. Tighten. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 23
Tighten or loosen to adjust height. With the string still attached, level the height of each column. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 24
Adjust inner columns to fit horizontal spacers. Tighen column hardware after spacing. Start from the left column. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 25
Continue adjusting inner columns to fit horizontal spacers until all are level. Tighen column hardware after spacing. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 26
Remove all spacers. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 32
ENG Display not included. 1/8" (3mm) 2020-07-01 #:146-9053-7 (2022-12-22)
Page 33
ENG Attach display, tighten connecting hardware, and run cables one at a time starting from the bottom left. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 35
ENG To remove, start from the top right. 2020-07-01 #:146-9053-7 (2022-12-22)
Page 36
Záruka Garantia TÜR Garanti̇ Garanzia Záruka www.peerless-av.com/warranty Peerless-AV Peerless-AV Europe Peerless-AV América Latina 2300 White Oak Circle Unit 2, Curo Park Av. de las Industrias 413 Aurora, IL 60502 Frogmore, St Albans, Parque Industrial Escobedo Email: tech@peerlessmounts.com Hertfordshire, AL2 2DD General Escobedo N.L., México 66062...