Advertisement
Quick Links
Advertisement
Related Manuals for peerless-AV DS-LEDVST Series
Summary of Contents for peerless-AV DS-LEDVST Series
- Page 1 DS-LEDVST Series *Actual configuration may vary 2022-01-13 #:146-9069-1...
- Page 2 WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. This product is designed to be installed on flat, unobstructed, vertical walls. Do not install on curved or angled walls. Before installing make sure the supporting surface will support the combined load of the equipment and hardware.
-
Page 3: Parts List
Parts (Before beginning, make sure you have all parts shown below). Refer to parts list included with your model. Parts List column vertical horizontal extrusion Description spacer A column B horizontal extrusion C vertical spacer D horizontal spacer E 3mm allen wrench two-tip T-handle F wall plate shim G connector plate H M5 x 5mm set screw... - Page 4 Optional: If connecting two top horizontal extrusions, first remove inner hook-on brackets. Remove and save hardware. Use extrusion connectors to connect top horizontal extrusions. G (4) H (8) Replace one hook-on bracket in between connected extrusions and tighten hardware. Use saved hardware. 2022-01-13 #:146-9069-1...
- Page 5 Secure additional hook-on brackets for top horizontal extrusions. 2022-01-13 #:146-9069-1...
- Page 6 Optional: If connecting two bottom horizontal extrusions, first remove inner hook-on brackets. Remove and save hardware. Use extrusion connectors to connect bottom horizontal extrusions. G (4) H (8) 2022-01-13 #:146-9069-1...
- Page 7 Replace one hook-on bracket in between connected extrusions. Use saved hardware. 2022-01-13 #:146-9069-1...
- Page 8 WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8"...
- Page 9 7/8" (22mm) minimum Use a laser level to keep mounting holes for mounting clearance level. 2.0" (51mm) display tile 2022-01-13 #:146-9069-1...
- Page 10 Level top horizontal extrusion and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick). 2022-01-13 #:146-9069-1...
- Page 11 1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). Level extrusion. Install using wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.). 2022-01-13 #:146-9069-1...
- Page 12 Edges must be flush. 1.34" Secure vertical spacers to the wall flush with the (34mm) horizontal extrusion. 3/8" (10mm) 2022-01-13 #:146-9069-1...
- Page 13 Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick). Edges must be flush. 1.34" (34mm) 2022-01-13 #:146-9069-1...
- Page 14 1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then install using wood screws 3/8" provided. (10mm) Maximum 80 in. • lb (9 N.M.). 2022-01-13 #:146-9069-1...
- Page 15 Remove vertical spacers. 3/8" (10mm) 2022-01-13 #:146-9069-1...
- Page 16 Hook on and secure all columns. Tighten hardware. 2022-01-13 #:146-9069-1...
- Page 17 Remove brackets from outer columns only. 2022-01-13 #:146-9069-1...
- Page 18 Loosen hardware on columns. 2022-01-13 #:146-9069-1...
- Page 19 Plumb and level outer columns, then tighten hardware. Tighten hardware on four corner wall plates. Tighten. Tighten. 2022-01-13 #:146-9069-1...
- Page 20 Tie a string between top slots on outer columns in order to level the depth of each. Loosen, adjust, tighten. Optional leveling for bowed walls Loosen. Insert. Tighten. 2022-01-13 #:146-9069-1...
- Page 21 Tie a string between bottom slots on outer columns in order to level the depth of each. Loosen, adjust, tighten. Optional leveling for bowed walls Loosen. Insert. Tighten. 2022-01-13 #:146-9069-1...
- Page 22 Tighten or loosen to adjust height. With the string still attached, level the height of each column. 2022-01-13 #:146-9069-1...
- Page 23 Adjust inner columns to fit horizontal spacers. Note location of holes. Tighten column hardware after spacing. Start from the left column. 2022-01-13 #:146-9069-1...
- Page 24 Continue adjusting inner columns to fit horizontal spacers until all are level. Note location of holes. Tighten column hardware after spacing. 2022-01-13 #:146-9069-1...
- Page 25 Remove all spacers. 2022-01-13 #:146-9069-1...
- Page 26 Optional: Flip wall bracket for additional depth as shown. 2.15" 1.80" (55mm) (46mm) 2.42" 2.86" (62mm) (73mm) 2022-01-13 #:146-9069-1...
- Page 27 Level L brackets and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick). 1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). 2022-01-13 #:146-9069-1...
- Page 28 Level L brackets. Install using wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.). 2022-01-13 #:146-9069-1...
- Page 29 Tie a string between center slots on outer columns in order to level the depth of each. 2022-01-13 #:146-9069-1...
- Page 30 Adjust depth, then remove string. Loosen, adjust, tighten. 2022-01-13 #:146-9069-1...
- Page 31 ENG Do not tighten connecting hardware. Not included. 2022-01-13 #:146-9069-1...
- Page 32 10-1 ENG Attach display, tighten connecting hardware, and run cables one at a time starting from the bottom left. 2022-01-13 #:146-9069-1...
- Page 33 10-2 2022-01-13 #:146-9069-1...
- Page 34 ENG To remove, start from the top right. 2022-01-13 #:146-9069-1...
- Page 35 This page intentionally left blank. 2022-01-13 #:146-9069-1...
- Page 36 Garantia TÜR Garanti̇ Garanzia Záruka www.peerless-av.com/warranty Peerless-AV Peerless-AV Europe Peerless-AV América Latina 2300 White Oak Circle Unit 3 Watford Interchange, Av. de las Industrias 413 Aurora, IL 60502 Colonial Way, Watford, Herts, Parque Industrial Escobedo Email: tech@peerlessmounts.com WD24 4WP, United Kingdom General Escobedo N.L., México 66062...
Need help?
Do you have a question about the DS-LEDVST Series and is the answer not in the manual?
Questions and answers