Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKOKI C 1806DA
Summary of Contents for HIKOKI C 1806DA
- Page 1 C 1806DA Handling instructions...
- Page 3 45° 30° 15° 0° 45° 0°...
- Page 4 45° 30° 15° 0°...
- Page 6 ⓑ ⓐ 4 mm 11 mm...
-
Page 7: General Power Tool Safety Warnings
c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi... - Page 8 h) Keep handles and grasping surfaces dry, clean c) Adjust the cutting depth to the thickness of the and free from oil and grease. workpiece. Slippery handles and grasping surfaces do not Less than a full tooth of the blade teeth should be visible allow for safe handling and control of the tool in below the workpiece.
-
Page 9: Additional Safety Warnings
e) Do not use dull or damaged blades. 14. Do not use saw blades which do not comply with the Unsharpened or improperly set blades produce narrow characteristics specifi ed in these instructions. kerf causing excessive friction, blade binding and 15. -
Page 10: Caution On Lithium-Ion Battery
33. Should lever remain loosened, it will create a very 1. Make sure that swarf and dust do not collect on the hazardous situation. Always thoroughly clamp it. battery. (Fig. 13) ○ During work make sure that swarf and dust do not fall on 34. -
Page 11: Regarding Lithium-Ion Battery Transportation
REGARDING LITHIUM-ION BATTERY SYMBOLS TRANSPORTATION WARNING The following show symbols used for the machine. When transporting a lithium-ion battery, please observe the Be sure that you understand their meaning before following precautions. use. WARNING Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output C1806DA: Cordless Circular Saw and follow the instructions of the transportation company... - Page 12 NOTE CHARGING Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to Before using the power tool, charge the battery as follows. change without prior notice. 1. Connect the charger’s power cord to the receptacle.
-
Page 13: Mounting And Operation
When replacing the new carbon brushes, always use to confi rm that the battery being charged with chargers genuine HiKOKI carbon brushes with the number are taken out, wait for a minimum of 3 seconds before specifi ed in the drawing. - Page 14 In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. Important notice on the batteries for the HiKOKI cordless power tools Space between Air gun Please always use one of our designated genuine lower guard batteries.
-
Page 15: Troubleshooting
TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. Symptom Possible cause Remedy Tool doesn’t run No remaining battery power Charge the battery. - Page 16 UC18YFSL BSL1850C C1806DA – – – – (NN)
- Page 17 BSL18.. BSL36..18 UC18YFSL (14.4 V–18 V) 322099 373460 325541 329897 302981 302756 944459 337528 378019...
- Page 20 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99742011 G Printed in China...
Need help?
Do you have a question about the C 1806DA and is the answer not in the manual?
Questions and answers