Preset Tuning - Pioneer VSX-5700S Operating Instructions Manual

AUTO OR MANUAL TUNING
1 2 3 5
AUTO tuning:
Auta tuning is convenient when you do not remember the frequency
of a desired station, or when you wish to find stations that you do not
normally listen to.
MANUAL tuning:
Each time the TUNING switch '+' or ''-"' is pressed, the tuning
frequency changes by one step, allowing you to find stations manually.
1. Press the POWER switch to the ON position.
NOTE:
Be sure to turn the TAPE 2 MONITOR switch OFF when listening to
AM or FM broadcasts.
2. Use the BAND selector switch to choose either FM or AM.
PRESET TUNING
BROADCAST RECEPTION
For AUTO tuning:-——-—— aa
3. Set the AUTO/MANUAL switch to the auto-tuning mode.
* in the Auto Tuning mode, the AUTO indicator will light.
4. Press the '' +" or '~"' of the TUNING switches.
* Pressing '+' causes scanning to take place in the direction of
increasing frequency. Pressing " ~"' causes scanning to take place
in the direction of decreasing frequency. at eS
* When a station is received, scanning will stop (the [TUNED |
indicator lights). If you wish to receive a different station, press
the TUNING switch "+" or ~"" again.
* When the received station is broadcasting a program in FM stereo,
the | STEREO | indicator will light.
* Pressing either of the TUNING (~-, +) switches during auto tuning
causes tuning to stop at the current frequency:
For MANUAL tuning: seen ee vn
3. Set the AUTO/MANUAL switch to the manual tuning mode.
* When in the Manual Tuning mode, the AUTO indicator will go out,
4. Press the ''+'' or ''~'' of the TUNING switch as necessary to set
to the frequency of the desired station.
Each time the switch is pressed, the tuning frequency will change
by one step in the direction corresponding to the switch pressed,
When keep depressed, the switch continues scanning until it is
released. .
* When a station is received, the | TUNED Jindicator will light up.
* When the received station is broadcasting a program in FM stereo,
the [STEREO | indicator will light up.
5. Adjust the volume and tone as desired.
NOTE:
* When Auto Tuning is used, correct reception may not be possibie
for very distant stations or stations with very weak signals, In this
event, | 4 Tuning is recommended.
* The| TUNED | indicator may not light with broadcasts received over
Jong distances, or when the broadcast signals are. extremely weak.
FREQUENCY PRESETTING
Allows three stations per STATION CALL switch (press once, twice,
or three times to select).
1. Press the POWER switch to the ON position.
NOTE:
Be sure to turn the TAPE 2 MONITOR switch OFF when listening to
AM or FM broadcasts.
2. Set the BAND selector to either FM or AM.
3. Tune in the desired station.
* See the section DIRECT ACCESS TUNING" for information on
reception using the Direct Access Tuning mode.
* See the section "AUTO TUNING" for information on reception
using the Auto Tuning mode.
* See the section "MANUAL TUNING'' for information on reception
using the Manual Tuning mode.
in addition to station frequencies, the FM MODE (AUTO/MONO}
can also be preset.
. Press the MEMORY switch.
5. Press the STATION CALL switch into which you wish to preset
the station.
* Use the STATION CALL switches ("1 ~- °9, *O} to select a preset
channel. One press selects the 1 — 10 range, two presses 11 ~
20, and three presses 21 ~ 30.
[Example] if you press key [+3
Once — STATION 3
Twice — STATION 13
Three times ~ STATION 23
Press a STATION CALL switch within two seconds.
6. Repeat steps 2 to 5 to preset additional stations.
Total of 30 AM and FM stations may be preset. When you store
a new preset, it takes the place of the previously stored station {it
any}.
Pp
23
<ARB1250>