Related Manuals for Taurus Dual Pro Multi-Press
Summary of Contents for Taurus Dual Pro Multi-Press
- Page 1 Assembly and Operating Instructions max. 180 kg ~ 180 Min. 225 kg L 199 | W 136 | H 168 SESS7130.01.01 SKU: SESS7130 Dual Pro Multi-Press...
- Page 2 Multi-Press...
-
Page 3: Table Of Contents
Content GENERAL INFORMATION Technical Data Personal Safety Set-Up Place ASSEMBLY General Instructions Scope of Delivery Assembly STORAGE AND TRANSPORT General Instructions TROUBLESHOOTING, CARE AND MAINTENANCE General Instructions Faults and Fault Diagnosis Maintenance and Inspection Calendar DISPOSAL RECOMMENDED ACCESSORIES ORDERING SPARE PARTS Serial Number and Model Name Parts List Exploded Drawing... - Page 4 Multi-Press...
- Page 5 With Taurus® fitness equipment, the focus is on what sport is all about: maximum performance! Therefore, the equipment is developed in close consultation with athletes and sports scientists.
- Page 6 ABOUT THIS MANUAL Please carefully read the entire manual before installation and first use. The manual will help you to quickly set up the system and explains how to safely use it. Make sure that all persons exercising with the equipment (especially children and persons with physical, sensory, mental or motor disabilities) are informed about this manual and its contents in advance.
-
Page 7: General Information
GENERAL INFORMATION Technical Data Weight and Dimensions Packaging dimensions (L x W x H) and article weight (gross, incl. packaging): Box 1: 163 cm x 91 cm x 19.5 cm 25 kg Box 2: 152 cm x 89 cm x 28.5 cm 35 kg Box 3: 160 cm x 102 cm x 46.5 cm... -
Page 8: Personal Safety
Personal Safety ⚠ DANGER Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year. -
Page 9: Set-Up Place
Set-Up Place ⚠ WARNING Do not place the equipment in main corridors or escape routes. CAUTION ⚠ Choose a location in which to place the equipment such that there is enough free space/ clearance to the front, the rear and to the sides of the equipment. The training room should be well ventilated during training and not be exposed to any draughts. -
Page 10: Assembly
ASSEMBLY General Instructions ⚠ DANGER Do not leave any tools, packaging materials such as foils or small parts lying around, as otherwise there is a danger of suffocation for children. Keep children away from the equipment during assembly. ⚠ WARNING Pay attention to the instructions attached to the equipment in order to reduce the risk of injuries. - Page 11 Number Name Quantity Frame Pulley set ( 114) Φ Pulley set ( Φ Pulley baffle Left shield + rear 005 + 008 + middle trim + right shield Left shield + front 005 + 009 + middle trim + right shield Side shield Tray Connecting strip...
- Page 12 Top weight Cable set Front floor frame Transverse 34-2 connecting frame Rear floor frame Seat cushion frame 35-2 Back cushion frame Support frame Rotary frame 36-2 Left arm frame 37-2 Right arm frame Balance weight Seat adjuster roller Back cushion Seat cushion Multi-Press...
- Page 13 Connecting rod frame Adjustment board Gas spring Weight stack tower 33-2 frame...
-
Page 14: Assembly
Assembly Before assembly, take a close look at the individual assembly steps shown and carry out the assembly in the order given. NOTICE First loosely screw all parts together and check that they fit properly. Tighten the screws using the tool only when you are instructed to do so. Step 1: Assembly of the Main Frame Fix the transverse connecting frame (34-2) to the frame (001) with four screws (027), four spring... - Page 15 Step 2: Assembly of the Floor Frames and Tower Frame Fix the weight stack tower frame (33-2) to the rear floor frame (41) with four screws (94), four spring washers (104) and four flat washers (106). Fix front floor frame (43) together with the weight stack tower frame (33-2) to the transverse connecting frame (34-2) with four screws (98), eight flat washers (106) and four nuts (111).
- Page 16 Step 3: Assembly of the Rotary Frame and Connecting Rod Frames Fix the rotary frame (38) to the weight stack tower frame (33-2) by threading a short spindle (58) through and securing with a circlip for shaft (83) on each side. Fix the connecting rod frames (44) to the rotary frame (38) with one screw (90) and one washer (67) each.
- Page 18 Step 4: Assembly of the Arm Frames Fix the right arm frame (37-2) to the weight stack tower frame (33-2) by threading one long spindle (57) and securing with one circlip for shaft (83) and one plastic washer (72) on each side of the long spindle (57).
- Page 19 33-2...
- Page 20 Step 5: Assembly of the Back Cushion Frame and Adjustment Boards Connect the front side of the two adjustment boards (51) with one screw (101), one seat adjuster roller (87), two flat washers (106) and one nut (111) [upper holes]. Now fix the rear side of the two adjustment boards (51) to the back cushion frame (35-2) with one screw (101), one seat adjuster roller (87), two flat washers (106) and one nut (111) [upper holes].
- Page 21 33-2...
- Page 22 Step 6: Assembly of the Seat Cushion Frame Fix two small spindles (59) to the seat cushion frame (42) with four screws (94), four spring washers (105) and four big washers (109). Fix the seat cushion frame (42) to the back cushion frame (35-2) with two small spindles (59), four screws (94), four spring washers (104) and four big washers (109).
- Page 23 35-2...
- Page 24 Step 7: Assembly of the Pulleys and Cable Routing NOTICE The majority of the pulleys are pre-assembled when delivered. These pulleys (68) need to be disassembled in order to perform the cable routing. The two pulleys for the frame (012 and 013) are not pre-assembled. Pass the cable (47) over the pulley (013, point A) and fix the pulley (013) to the upper side of the frame (001) and pulley baffle (004) with the pre-assembled screw (026), two flat washers (031) and one nut (034-1).
- Page 25 Correct Wrong 034-1 Cable Cable limiting post limiting post 034-1...
- Page 26 Step 8: Assembly of the Cushions Fix the seat cushion (56) to the seat cushion frame (42) with four screws (93), four spring washers (103) and four flat washers (105). Fix the back cushion (55) to the back cushion frame (35-2) with four screws (93), four spring washers (103) and four flat washers (105).
- Page 28 Step 9: Assembly of the Weight Plates and Labels NOTICE The guide rods are pre-assembled to the frame. Disassemble the upper part of the guide rods (002) by removing the screws (021), the guide rod fixing sleeves (003), the split washers (028) and the bumpers (014). Carefully slide each of the weight stack plates (82) over the guide rods (002) one by one.
- Page 29 Name Specification Qty. Frame Guide rod Guide rod fixing sleeve Bumper Φ38*Φ21*10 Select pin set Hexagon socket set s with cone M8*20 Split washer d=20 Top weight plate 10lb weight stack plate 4.5 kg...
- Page 30 Step 10: Assembly of the Shields and Trims NOTICE The left and right shields are pre-assembled with a front or rear middle trim. Make sure to align the shields in the respective direction (front/rear). Fix the left and right shields (005 & 006) with the rear and front middle trim (008 & 009) to the frame (001) with four screws (022).
-
Page 32: Storage And Transport
STORAGE AND TRANSPORT General Instructions ⚠ WARNING The storage location should be chosen so that improper use by third parties or children can be prevented. If your equipment does not have transportation wheels, the equipment must be disassembled before transportation. ࣑... -
Page 33: Troubleshooting, Care And Maintenance
TROUBLESHOOTING, CARE AND MAINTENANCE General Instructions ⚠ WARNING Do not make any improper changes to the equipment. CAUTION ⚠ Damaged or worn components may affect your safety and the life of the equipment. Therefore, immediately replace damaged or worn components. In such a case, contact the contract partner. -
Page 34: Maintenance And Inspection Calendar
Maintenance and Inspection Calendar To avoid damage from body sweat, the equipment must be cleaned with a damp towel (no solvents!) after each training session. The following routine tasks must be performed at the specified intervals: Part Weekly Monthly Cables Screw connections Pulleys and cable routing Slide rails/Guide rods... -
Page 35: Recommended Accessories
RECOMMENDED ACCESSORIES To make your training experience even more efficient and pleasant, we recommend that you add suiting accessories to your fitness equipment. This could be a floor mat, for example, which makes your fitness equipment stand more securely and also protects the floor from falling sweat, but it could also be additional handrails on some treadmills or silicone spray to keep moving parts in good shape. -
Page 36: Ordering Spare Parts
The serial number of your equipment is unique. It's located on a white sticker. The exact position of this sticker is shown in the following illustration. Enter the serial number in the appropriate field. Serial number: Brand / Category: Taurus / multi gym Model Name: Dual Pro Multi-Press SKU: SESS7130... -
Page 37: Parts List
Parts List Name Specification Qty. Frame Guide rod Guide rod fixing sleeve Pulley baffle Left Shield Right Shield Side Shield Rear middle Trim Front middle Trim Connecting strip Pulley set φ89*25.8 Pulley set φ114*32 Bumper φ38*φ21*10 Floor mat Bumper φ62*φ20*26 Guide rod upper cap Hook stop collar Single Side glue cushion... - Page 38 Flat washer Φ24*Φ13*2.5 033-1 Spring washer 034-1 Nylon nut 035-1 Nut 036-1 Stopple Φ10*Φ5.3*1 037-1 Elastic cylindri cal pin φ10*45 33-2 Weight stack tower frame 34-2 Transverse connecting frame 35-2 Back cushion frame 36-2 Left arm frame 37-2 Right arm frame Rotary frame Adjustment frame Support frame...
- Page 39 Rolling bearing Camshaft M20 mut Pilot plunger Spring Washer Pulley set Tube plug rubber mat Rubber bumper Plastic washer Handle grip Handle grip Handle grip Rotary knob Aluminum end cover Aluminum ring Aluminum ring Plastic ring Top weight 4.5KG 10lb weight stack plate 4.5KG circlip for shaft d0=25...
- Page 40 socket cap screw M10*65 socket cap screw M10*80 socket cap screw M10*85 socket cap screw M10*95 socket cap screw M10*130 spring washer spring washer spring washer Flat washer Φ16*Φ8.4*1.6 Flat washer Φ20*Φ10.5*2 big washer Φ24*Φ8.4*2 Flat washer Φ30*Φ17*3 big washer Φ34*Φ11*3 hexagon nut Flat washer...
-
Page 41: Exploded Drawing
Exploded Drawing... - Page 42 Exploded View Multi-Press...
-
Page 43: Warranty
WARRANTY Training equipment from Taurus® is subject to strict quality control. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline. - Page 44 Warranty Conditions For the warranty to be valid, the following steps must be taken: Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance.
-
Page 45: Contact
CONTACT TECHNICAL SUPPORT TECHNICAL SUPPORT & SERVICE TECHNICAL SUPPORT & SERVICE �� �� �� +49 4621 4210-900 80 90 16 50 +33 (0) 172 770033 +49 4621 4210-945 +49 4621 4210-933 �� +49 4621 4210-698 �� �� info@fitshop.dk service-france@fitshop.fr �� technik@sport-tiedje.de ��... - Page 46 LIVE FITNESS WEBSHOP AND SOCIAL MEDIA Sport-Tiedje is Europe’s largest specialist store www.sport-tiedje.co.uk for home fitness equipment with currently over www.sport-tiedje.de/blog 70 stores and one of the world’s most renowned online mail order companies for fitness equipment. Private customers order via the 25 www.facebook.com/SportTiedje web shops in the respective national language or have their desired equpiment assembled on...
- Page 48 Dual Pro Multi-Press...