Setting The Clock (Auto / Manual) - FUNAI F19TRG1 Owner's Manual

SETTING THE CLOCK
(AUTO / MANUAL)
Set the clock accurately for proper automatic timer re¬
cording. If the Public Broadcasting Station (PBS) is
available in your area, follow "AUTO CLOCK SET¬
TING". If it is not, follow "MANUAL CLOCK SET¬
TING".
AUTO CLOCK SETTING
You can have the TV/VCR set the clock automatically
by using the Public Broadcasting Station (PBS) channel
in your area. Once you have set the clock by using the
following procedure, the TV/VCR will automatically
monitor the correct time and date being broadcast by the
PBS station in your area, using a new service called Ex¬
tended Data Service (XDS).
Make sure...
• Press POWER button to turn on the TV/VCR set.
• Confirm that the antenna connections are correct.
• The cable converter box must be turned on if your
TV/VCR is connected directly to it. (See NOTES:)
• You must use the remote control for the following
steps.
• The channel you want to record is properly set in
advance.
NOTES:
• Auto clock setting only has to be done one time. You
may set the clock only if the clock's time has become
incorrect for some reason.
• If the TV/VCR is connected directly to a cable con¬
verter box, the local PBS station must be selected on
the cable box itself, and the TV/VCR must be set to
the output channel of the cable converter box (usually
channel 3 or 4), to be able to set up or correct the
clock automatically.
The TV/VCR cannot control the channels of the ca¬
ble converter box.
• If there is no local PBS station in your area or on your
cable system, proceed to MANUAL CLOCK SET¬
TING on page 15.
1 Select "SETTING CLOCK"
Press MENU button.
f
-MENU-
Press PLAY/A or STOP/V but¬ »CfUBE CONTROL
►
SETTING CLOCK
ton repeatedly to point to "SET¬
CHANNEL SET UP
USERS SET UR
tAKGUAGE •ENOJSK
TING CLOCK".
CAPTON (OFF.
HUE SEARCH
Then, press F.FWD/>- button.
2 Set "AUTO CLOCK" to
[ON]
Press F.FWD/*- or REW/-4 but¬
ton repeatedly until [ON] ap¬
pears.
3
Enter the channel number for the PBS station
Press PLAY/A or STOP/T but¬
ton repeatedly to point to
"AUTO CLOCK CH".
Then press F.FWD/^ or
RF.WAM button repeatedly until
the channel number for your lo¬
cal PBS station appears.
If you do not know the PBS channel number, remain on
[AUTO], The TV/VCR will automatically search all
available channels for the local PBS station, and will se¬
lect dial channel.
4 Exit the Auto Clock Setting
Press MENU button to return to the TV mode.
5 Turn off the TV/VCR
Press POWER button to turn oil the TV/VCR for search
ing the local PBS station. The power must remain off
during this search.
If you enter the channel number manually,
• It may take a few minutes for this search to be com¬
pleted.
If you choose [ALTO],
• The TV/VCR must search through all the available
channels one by one, starting with the lowest num¬
bered channel. It must scan each channel for a couple
of seconds to determine if that channel is transmitting
the XDS signal. This search could take up to 10 min¬
utes if the local PBS station is on a high numbered
channel in your area or on your cable system.
If the time that is automatically set by this selected
PBS station is incorrect, it may not be your local PBS
station, but one from a different time zone. Or there
is a possibility that no channel in your area is broad¬
casting the XDS signal, as evidenced by no time be¬
ing set even after 10 minutes search. In these cases,
you must manually enter the correct local PBS sta¬
tion, or set the clock manually and turn off the Auto
Clock Setting feature.
- SETTING CLOCK -
AUTO CLOCK |C|0
AUTO CLOCK CM w
MANUAL CLOCK SET
0 6.T
ICfFj
- SETTT*3 CLOCK -
AUTO CLOCK
MANUAL CLOCK SET
D.S.T |CFF]
-
14
-
EN
61.13