Table of Contents
Advertisement
Quick Links
LAZO
Floor Standing Bath Shower Mixer
i
Important Information BEFORE YOU START
Please read carefully and keep this information for further reference.
All products manufactured and supplied by Crosswater are
safe provided they are installed, used correctly and receive
regular maintenance in accordance with these instructions. If
you are in any doubt about your ability to install this product
safely you must employ the services of an experienced
meet the requirements of the Water Supply (Water Fittings)
Regulations 1999 and Scottish Byelaws 2004.
Operating pressure range: Minimum 0.2 bar, Maximum 5.0 bar.
Maximum static pressure: 10.0 bar.
Note: Nominally equal (balanced) inlet supply pressures are
recommended for optimum performance with mixer t
1
Designed to comply with BS EN 200 for single taps /
combination taps and BS EN 817 for single lever mixers, for
and to be used within systems designed to BS 6700.
BS 6700 recommends the temperature of stored water should
never exceed 65°C.
meet all normal requirements and will minimise the build up
of lime scale in hard water areas.
minimum distance from the highest installed position of the
outlet to the underside of the cold tank should be at least 2
aps.
metres to ensure adequate performance.
PRODUCT CODES:
LA1416FC/F/M
V10623
®
Advertisement
Table of Contents
Related Manuals for Crosswater Lazo LA1416FC
Summary of Contents for Crosswater Lazo LA1416FC
- Page 1 IMPORTANT INFORMATION BEFORE YOU START Please read carefully and keep this information for further reference. All products manufactured and supplied by Crosswater are Designed to comply with BS EN 200 for single taps / safe provided they are installed, used correctly and receive combination taps and BS EN 817 for single lever mixers, for regular maintenance in accordance with these instructions.
- Page 2 ® DIMENSIONS NOTE: ALL DIMENSIONS IN MILLIMETRES IMPORTANT INFORMATION Please read carefully and keep this information for further reference. These taps and mixers should be installed in compliance with the Water Regulations. Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the mains, approved check valves must be For further details contact your Local Water Authority.
- Page 3 ® BEFORE YOU START Important Pre-Installation Notes Warning: Before starting any installation please consider the following: before drilling into walls, check that there are no hid- den electrical wires, cables or wate supply pipes. This can be checked with the aid of an electronic detector. If power tools are used do not forget to: - Wear eye protection Important:...
- Page 4 ® COMPONENTS SPOUT HANDSET CONNECTION SCREW DIVERTER HOSE CONE HANDLE Shower Hose UPSTAND PIPE SPIRIT LEVEL PLASTIC COVER DRAIN CONNECTION DRAIN PLATE FLOOR BOLTS...
- Page 5 ® INSTALLATION Minimun depth in SPIRIT LEVEL the ground MINIMUM DEPTH HOT INLET COLD INLET Ho e mm The floor needs to be prepared by making a cavity at least Mark 4 points on the ground where the fixing seat will be 50mm indepth within a solid floor.
- Page 6 ® INSTALLATION DRAIN CONNECTION SCREW PLASTIC PLASTIC HOSE COVER DRAIN PLATE HOSE POINT HOT INLET COLD INLET HOT INLET COLD INLET Proceed with the air &water tests of the valves and pipes should be flushed of all debris etc again connections.
- Page 7 ® INSTALLATION UPSTAND PIPE COVER PLATE COVER PLATE CORE SCREW FIXING SEAT FIXING HOT INLET COLD INLET FLANGE FIXING SEAT On the main body of the product slide the cover plate up Rotate the fixing flange to adjust the spout direction properly. This fixing flange can be rotated 360°.
- Page 8 Once all loose debris and dirt has been cleared, replace the aerator into the spout and tighten with the key provided Lake View House Rennie Drive, Dartford Part of the Kent DA1 5FU Bathroom Brands Group United Kingdom 0345 873 8840 www.crosswater.co.uk...
Need help?
Do you have a question about the Lazo LA1416FC and is the answer not in the manual?
Questions and answers