After Use; Troubleshooting - Tarrington House K103M1BME3-1 Assembly Instructions Manual

Table of Contents

Advertisement

Available languages

Available languages

7. Ignite the other burners using their respective control knobs after the first burner has fired up.
Side burner
To get the maximum yield with the minimum consumption of gas, keep the following points in mind:
Once the burner has been alighted, adjust the flame according to your needs, from LO to HI position.
Use proper pan size (with flat bottom only) for each burner.
When the content of the pan starts to boil, turn the knob down to LO (small flame).
Always put a lid on the pan.
Use pans sized Ø 20-24 cm.
APPEARANCE OF THE FLAME
The flame should appear blue and stable. There should be no yellow sparks, loud noises nor should there be
distance between the base of the flame and the nozzle.
A yellow flame indicates insufficient oxygen supply. Loud noises and the flame being distant from the nozzle
indicate excessive oxygen supply.
Check the appearance of the flame at every use. Contact a specialist to reset the appliance should the
appearance differ from normal.
TIPS REGARDING BURNING GREASE
WARNING!
Protect yourself and your hands from spurts of flames. Never try to put out a grease fire with water! Turn all the control knobs to the off positions
OFF, if a grease fire occurs. Turn the gas supply on the gas cylinder or the pressure regulator off and wait until the fire goes out by itself.
Grease and juice that drips from meat onto the heater produces short spurts of flames which also contribute to the grilling taste.
If too many spurts of flames are produced, the meat could burn.
Only use meat that is suitable for grilling. Try to avoid grilling meat with excessive fat.
Before grilling meat, cut away as much fat as possible and do not overuse marinade to prevent meat from burning.

AFTER USE

1. Close the valve on the gas cylinder or the pressure regulator. Wait until the flame extinguishes completely in the appliance.
2. Turn all the control knobs to off positions OFF and let the appliance cool for about 5 minutes. The cover must be open at this time.
3. Disconnect the gas cylinder from the appliance and dismount the gas cylinder (
reattach the orange safety cap on the gas cylinder.
4. Clean (
CLEANING, MAINTENANCE AND CARE) and store the appliance (
appliance again soon.

TROUBLESHOOTING

Suspected malfunctions, errors or damage are often due to causes that the users can fix themselves. Therefore check the appliance using the below table
before contacting a qualified specialist. In most cases the problem can be solved quickly.
WARNING!
Only perform the steps described within this instruction manual! All further inspection, maintenance and repair work must be performed by an
authorised service centre or a similarly qualified specialist!
Problem
The appliance does not ignite immediately.
The appliance does not ignite at all.
No spark noise.
Pressure regulator makes noise.
Possible cause and solution
Ensure that the gas valves are open.
Check if sparks are produced when igniting the appliance.
Push the control knob for 5 seconds before you attempt to ignite the appliance.
Ensure that the burners are clean.
Check if the gas cylinder is not empty.
The electrode does not aim at the burner hole. Align the electrode and the burner hole. Adjust the distance
between metal pin of the electrode and burner hole to 3-5 mm.
Obstructions in burners. Clean burners.
Obstructions in gas jets or hose. Clean jets and hose.
The wire between metal pin and ignitor is off. Connect the wire.
The electrode does not aim at the burner hole. Align the electrode and the burner hole. Adjust the distance
between metal pin of the electrode and burner hole to 3-5 mm.
Check if the ventilation opening on the pressure regulator is plugged. Unplug the opening and wait
5 minutes before starting again.
Check if the ventilation openings are covered up. Check the appearance of the flames and remove possible
plugging.
- 11 -
Mounting / dismounting the gas cylinder). If the gas cylinder is empty,
STORAGE AND TRANSPORTATION) if you do not plan to use the
GB

Advertisement

Table of Contents
loading

Table of Contents