Listening To A Source Component.15; Adjusting The Sound.15 - Kenwood VR Series Instruction Manual

Listening to a source component
Adjusting the sound
VR/KRF-V SERIES (En/KM)
VOLUME CONTROL
D
Use the input selector (INPUT SELECTOR (AUDIO, VIDEO))
to select the source you want to listen to.
The Input sources change as shown Mow:
Selecting a source using the INPUT SELECTOR knob
^ O TUNER
e -cD^rcD"*)
0 "TAPE" or-MD" ("TAPE"*)
O "PHONO"("PHONO"*)
O "VIDE01"<"VCRr")
O "VIDE02" (''VCR2"*)
U O "DVD 6ch"
SOURCE DIRECT VOLUME CONTROL
BASS BOO 5T
SC UND
MMiax
□
1—»
m
T
)
o 1 o
T
1
PHONES
MULTI CONTROL
SPEAKERS A/B (KRF-6020)
SPEAKERS, MUTE (except for KRF-6020)
VIDEO
VOLUME
TUNING/SKIP
MUTE
SOUND
VOLUME
MUTE
SOUND-p|3|'
MULTI CONTROL m
a a o o j
RC-R0711
Adiusfing the tone
The following adjustments are possible if the receiver is in the stereo
mode,
O Press the SOUND key to select the tone mode to be adjusted.
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
Selecting a source using the AUDIO key
on the remote control (RC-R060B)
O "CD" ("CD"*)
0 "TAPE" or "MD" ("TAPE"*)
O TUNER
O "PHONOTPHONO"*)
Selecting a source using the VIDEO key
on the remote control (RC-R0608)
O "VIDEOr("VCR1"*)
0 "VIDE02"("VCfl2"*)
0 "DVDSch"
• When selecting an input source by using the remote control (RC-
ROT It), press the desired input selector key.
• "VIDEO 2" can be selected as an input source only if the VIDEO 2/
MONITOR setting is "VIDEO 2". -C£i
• Oncesetup codes are registered in the remote control (RC-R0608).
the input name display changes according to the name of the
registered component.
Example: if you register a VCR at the VIDE01 jacks. 'VCR* appears
instead of 'VIDEO V RC-CX]
• When using the remote control (RC-R0608) after initial setup, any
inputs that have not been registered with a setup code are deleted
from the cyclic list. RC-QQ
• The INPUT SELECTOR on the front panel of the receiver always
cycles through all inputs.
'EJ 1
~
0 Use the MULTI CONTROL (TUNING/SKIP) to adjust tha aound
quality.
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
• The adjustment item is displayed for approximately 8 seconds.
• If you used the remote control (RC-R0608) to perform the atxive
setting, press the VIDEO key at this point to turn off the remote
control's own adjustment mode. In this case, the input source is not
switched.
Once-tottch low frequency emphasis (bass boost)
The following adjustments are possible if the receiver is in the stereo
mode
Press ths BASS BOOST ksy.
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality
or ambience effects adjustment mode.
Q
Start playback from the selocled source. Switching back lo the previous setting
_ Press the BASS BOOST key sgsin.
B
Use the VOLUME CONTROL (VOLUME) to adjust the
volume.