In Ease Of Difficulty - Kenwood VR Series Instruction Manual

VB/KWF-V SERIES (En/KMI
Resetting the Microcomputer
W the microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) H the power cord is unplugged
while the poarer Is ON, or due to some other external factor. If this
happens, execute the following procedure to reset die micro¬
computer and return the unit to its normal operating condition.
For U.S.A. and Canada_
Unplug the power cord from the wall outlet, then plug it
back In while holding down the POWER key.
For other countrlee__
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY key,
press POWER._
• Please note that resetting the microcomputer will clear the contents
of the memory and returrts the unit to the state it was in when it left the
factory.
Amplifier
^ ....... ''
- ■■ ■
No sound from the speakers.
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
• Connect them properly referring to "Connect¬
ing the speakers" -22
• Adjust the volume to a proper level.
• Turn OFF the MUTE. -CSj
• Set the SPEAKERS switch(es) to ON. -CS;
The standby indicator blinks and sound Is
not output.
• Speaker cords are short-circuited.
• Turn the power off, eliminate the short-circuit¬
ing, then turn on the power again. -22
Sound is not output from one of the apaakars.
• The speaker cord is disconnected
* Connect it properly referring to "Connecting
the speakers".
Sound ia not output from the surround
speakers and / or the center speaker, or thair
sound Is very small.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• A surround mode has not been engaged,
• The surround and/or center volume controls
are set to the minimum level.
• Connect it properly referring to "Connecting
the speakers".
• Select a surround mode
• Adjust the speaker levels using the lest tone.
A humming noise ia generated whan the
PHONO input selector ia selected.
• The audio cord from the turntable Is not con¬
nected to the PHONO jacks.
• The turntable is not grounded.
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND termi¬
nal on the rear panel.
Tuner
Radio stations cannot be received.
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
Interference.
• Noise due to ignition noise from an automo¬
bile.
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
• Install the outdoor antenna away from the
road.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
A station which was preset cannot be ra-
celvad by pressing the corresponding nu¬
meric key.
• The preset station belongs to a frequency that
cannot be received
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
• Preset a station with a receivable frequency.
• Preset the station again.
Remote controi unit
__ mm.
Remote control operation Is not possible.
• Batteries are exhausted.
• The remote control unit is too far away from the
main system, controlling angle is too large, or
there is an obstacle between the receiver and
the remote.
• The audio cords and system control cords are
not connected properly.
• No software is loaded in the source compo-
r^ent.
• An attempt is made to play a tape which is
being recorded in the cassette deck.
• Replace with new batteries. -Q2-2B
• Operate the remote control unit within the
controllable range.
• Connect properly referring to "Setting up the
system". "*00
• Place software in the source component you
want to play.
• Wail until recording has completed.