Mitsubishi Electric FR-A520-0.4K-NA Instruction Manual page 7

z
Base frequency, base frequency voltage (Pr. 3, Pr. 19, Pr. 47, Pr. 113).................................................................65
z
Multi-speed operation (Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr. 232 to Pr. 239) ..............................................................66
z
Acceleration/deceleration time (Pr. 7, Pr. 8, Pr. 20, Pr. 21, Pr. 44, Pr. 45, Pr. 110, Pr. 111) ..................................67
z
Electronic overcurrent protection (Pr. 9)..................................................................................................................68
z
DC dynamic brake (Pr. 10, Pr. 11, Pr. 12)...............................................................................................................69
z
Starting frequency (Pr. 13) ......................................................................................................................................70
z
Load pattern selection (Pr. 14) ................................................................................................................................70
z
Jog operation (Pr. 15, Pr. 16) ..................................................................................................................................71
z
MRS input selection (Pr. 17) ...................................................................................................................................72
z
Stall prevention (Pr. 22, Pr. 23, Pr. 66, Pr. 148, Pr. 149, Pr. 154)...........................................................................73
z
Multi-speed input compensation (Pr. 28).................................................................................................................74
z
Acceleration/deceleration pattern (Pr. 29, Pr. 140 to Pr. 143).................................................................................75
z
Regenerative brake duty (Pr. 30, Pr. 70).................................................................................................................76
z
Frequency jump (Pr. 31 to Pr. 36) ...........................................................................................................................77
z
Speed display (Pr. 37, Pr. 144) ...............................................................................................................................78
z
Up-to-frequency sensitivity (Pr. 41) .........................................................................................................................79
z
Output frequency detection (Pr. 42, Pr. 43, Pr. 50, Pr. 116) ...................................................................................79
z
Second/third stall prevention (Pr. 48, Pr. 49, Pr. 114, Pr. 115) ...............................................................................80
z
Monitor display/FM, AM terminal function selection (Pr. 52 to Pr. 54, Pr. 158) ................................................ .......82
z
Monitoring reference (Pr. 55, Pr. 56).......................................................................................................................84
z
Automatic restart after instantaneous power failure (Pr. 57, Pr. 58, Pr. 162 to Pr. 165) .........................................85
z
Remote setting function selection (Pr. 59) ..............................................................................................................87
z
Intelligent mode selection (Pr. 60)...........................................................................................................................88
z
Acceleration/deceleration reference current/lift mode starting frequency (Pr. 61 to Pr. 64)................................... .90
z
Retry function (Pr. 65, Pr. 67 to Pr. 69) ...................................................................................................................91
z
Applied motor (Pr. 71) .............................................................................................................................................93
z
PWM carrier frequency (Pr. 72, Pr. 240) .................................................................................................................94
z
Voltage input (Pr. 73) ..............................................................................................................................................95
z
Input filter time constant (Pr. 74) .............................................................................................................................96
z
Reset selection/PU disconnection detection/PU stop selection (Pr. 75) ......................................................... ........96
z
Alarm code output selection (Pr. 76) .......................................................................................................................98
z
Parameter write inhibit selection (Pr. 77) ................................................................................................................99
z
Reverse rotation prevention selection (Pr. 78) ......................................................................................................100
z
Operation mode selection (Pr. 79) ........................................................................................................................101
z
Motor capacity/number of motor poles/speed control gain (Pr. 80, Pr. 81, Pr. 89) .............................................. .104
z
Offline auto tuning function (Pr. 82 to Pr. 84, Pr. 90 to Pr. 94, Pr. 96) ..................................................................105
z
Online auto tuning selection (Pr. 95) .....................................................................................................................111
z
V/F control frequency (voltage) (Pr. 100 to Pr. 109)..............................................................................................113
z
Computer link operation (Pr. 117 to Pr. 124).........................................................................................................114
z
PID control (Pr. 128 to Pr. 134) .............................................................................................................................124
z
Commercial power supply-inverter switch-over function (Pr. 135 to Pr. 139).................................................... ....131
z
Output current detection function (Pr. 150, Pr. 151)..............................................................................................135
z
Zero current detection (Pr. 152, Pr. 153)...............................................................................................................136
z
RT signal activated condition selection (Pr. 155) ..................................................................................................137
z
Stall prevention function and current limit function (Pr. 156).................................................................................137
z
OL signal output timer (Pr. 157) ............................................................................................................................139
z
User group selection (Pr. 160, Pr. 173 to Pr. 176) ................................................................................................140
z
Watt-hour meter clear/actual operation hour meter clear (Pr. 170, Pr. 171) .........................................................141
z
Input terminal function selection (Pr. 180 to Pr. 186) ............................................................................................141
z
Output terminal function selection (Pr. 190 to Pr. 195) .........................................................................................144
II