Medical Device Combinations It may be possible to configure this Permobil wheelchair with one or more other Medical Devices, accessories, or products. In the event that a provider wishes to do so, a risk assessment should be performed by competent equipment providers to ensure the safety and efficacy of the combination. Any installation of aftermarket equipment that requires permanent modifications to the wheelchair will void the manufacturer’s warranty.
Permobil TiLite CR1 Service Manual Replacing Parts on the TiLite CR1 Caster Wheels Parts: Tools: 1. Axle Bolt - M5x16 FHCS with Thread Patch 1. 3mm Hex Wrench 2. Caster Cap 2. Torque Wrench 3. Caster 4. Axle IMPORTANT! When replacing caster wheels, both casters need to be replaced at the same time to maintain proper ride quality.
Permobil TiLite CR1 Service Manual Replacing Parts on the TiLite CR1, continued Footrest Parts: Tools: 1. Footrest 1. 4mm Hex Wrench 2. Clamp Bolt - M5x22 SHCS 2. Torque Wrench 3. Clamp Housing 3. Mallet 4. Clamp Wedge IMPORTANT! Verify that the correct seat to footrest measurement is achieved and the footplate is level with the ground. Also check for floating casters, as sometimes floating casters can happen after an adjustment to the footrest is made.
The snap buttons should be pointing towards the outboard side of the Retention wheelchair on both sides of the wheelchair. Only the first snap button Snap Button should be engaged. 2. To set the anti-tip wheel in the correct location, refer to the "Fitting the TiLite CR1, Anti-Tips" section. Anti-Tip Receiver...
8. Strut Spacers 9. Frame Clamp 10. Frame Clamp Screws - M5x16 SCHS IMPORTANT! If the replacement camber tube has a different camber, the Center of Gravity will need to be adjusted per "Fitting the TiLite CR1, Center of Gravity" section. Removal: 1.
10. Frame Clamp 11. Frame Clamp Screws - M5x16 SHCS IMPORTANT! If adding or removing spacers, the Center of Gravity may need to be adjusted per the "Fitting the TiLite CR1, Center of Gravity" section. Removal: 1. Loosen and remove the bottom clamp screws and the camber tube bracket on both sides of wheelchair.
10. Frame Clamp 11. Frame Clamp Screws - M5x16 SHCS IMPORTANT! If installing any other replacement parts on the Center of Gravity, the Center of Gravity may need to be adjusted per the "Fitting the TiLite CR1, Center of Gravity" section.
Rear Tire Inflation It is very important to maintain proper tire inflation for best performance and tire life. Air pressure in the tire drops gradually over time and use. Permobil recommends checking the tire pressure every 2-3 weeks at minimum and filling to the maximum pressure listed on the sidewall of the tire. If the air pressure has dropped, refill to the listed maximum pressure to maintain performance.
Permobil TiLite CR1 Service Manual Troubleshooting, continued Adjusting Toe-In / Toe-Out Tools needed: 1. 4mm Hex Wrench 2. 23mm Open End Wrench 3. Ruler or Tape Measure 4. Felt Tip Pen Note: Adjusting toe-in / toe-out does not apply to wheelchairs with 0° camber; however, it is still necessary to make sure that the camber plug flats are perpendicular to the ground.
Hair and other debris caught in the caster axle is a common problem that causes a decrease in performance. To check for hair, remove the caster cap as shown in the "Replacing Parts on the TiLite CR1, Caster Wheels" section. Look for debris wrapped around the axle. If debris is found, remove and clean prior to reassembly.
Page 20
PD13917 Rev. 2023-08-29 TiSport, LLC 2701 W. Court St. Pasco, WA 99301 permobil.com...