Permobil Chairman Basic Service Manual
  1. Manuals
  2. Brands
  3. Permobil Manuals
  4. Wheelchair
  5. Chairman Basic
  6. Service manual
Permobil Chairman Basic Service Manual

Permobil Chairman Basic Service Manual

Hide thumbs Also See for Chairman Basic:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Operator's Manual

SERVICE MANUAL

Chairman Basic

Chassinr. 400 001-
US

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Chairman Basic and is the answer not in the manual?

Questions and answers

Related Manuals for Permobil Chairman Basic

Summary of Contents for Permobil Chairman Basic

  • Page 1: Service Manual

    SERVICE MANUAL Chairman Basic Chassinr. 400 001-...

  • Page 3: Table Of Contents

    Contents Introduction .....................3 Technical support..................3 Spare parts ....................3 Warranties....................3 Maintenance ....................3 Rating plates ....................4 Chairman Basic ...................4 Control unit ....................4 Raising the seat lift..................5 Covers......................6 Removal.......................6 Fitting ......................6 Changing the batteries...................7 Removal.......................7 Fitting ......................8 Changing the drive wheel ................9 Removal.......................9 Fitting ......................9...

  • Page 4: Introduction

    In the event of Technical Problems, you should contact your dealer, or Pemobil Inc at 800-736-0925 Spare parts Spare parts must be ordered through your dealer. The spare parts catalogue for the Chairman Basic chassis is PAB 1224 and is available from Permobil Inc. Warranties The Warranty Manual, PAB 9533, contains information on the current warranties available from Permobil AB.

  • Page 5: Rating Plates

    Rating plates Rating plates Chairman Basic Identity marking Chassis no. Control unit/ panel Identity marking Art. no. Serial no. Modification no.

  • Page 6: Raising The Seat Lift

    Raising the seat lift Raising the seat lift manually If the seat lift cannot be raised in the normal manner because the batteries are discharged or the adjustment device is defective, the seat can be raised manually. Remove the cushion and the seat plate. Raise the seat using the seat lift crank provided.

  • Page 7: Covers

    Cover Cover Removal Raise the seat to its highest position. Loosen the three plastic knobs which hold the cover in place. Remove the cover. Fitting Place the cover on the chassis. Tighten the three plastic knobs which hold the cover in place.

  • Page 8: Changing The Batteries

    Changing the batteries Changing the batteries NB. Use protective goggles when working with batteries. Removal Raise the seat to its highest position. If the battery is defective, see Raising the seat lift on page 6. Remove the chassis cover. It is held in place by three plastic knobs.

  • Page 9: Fitting

    Changing the batteries Fitting Replace the chassis cover and set the seat to the correct height again. Tighten the seat If the wheelchair is fitted with acid batteries, tube brace. check that the battery fluid is at the right level. Charge the batteries.

  • Page 10: Changing The Drive Wheel

    Changing the drive wheel Changing the drive wheel Removal Raise and block up the wheelchair's chassis so that the wheel does not reach the ground. Loosen and remove the centre screw C, the washer B and the rim locking washer A (see the figure at the bottom of the page).

  • Page 11: Changing The Brake Release Wires

    Changing the brake release wires Brake release mechanism Fitting Changing the brake release wires Fit the wire first at the magnetic brake and The upper wire controls the left brake unit and the then at the release lever. lower wire controls the right brake unit. Adjust the length of the wire sleeve using Removal the adjusting screw (2) so that the wire is...

  • Page 12: Changing The Magnetic Brake

    Changing the magnetic brake Changing the magnetic brake Removal Raise the seat to its highest position. Remove the chassis cover, which is held in place by three plastic knobs. Loosen the electrical connection of the magnetic brake. Electrical connection of the magnetic brake Detach the brake release wire from the brake.

  • Page 13: Fitting

    Changing the magnetic brake Fitting Check the setting of the brake. Follow the instructions on the decal on how the two Allen screws are adjusted. Place the magnetic brake's brake disc in the brake assembly. Put on the cover.
  • Page 14 Changing the magnetic brake Insert a screw to align the parts and screw the magnetic brake in place using all three screws. Attach the magnetic brake's electrical connection. Fit the chassis cover, see Covers, page 7. The magnetic brake's electrical connection...

  • Page 15: Changing The Drive Motor

    Changing the drive motor Changing the drive motor Removal Raise the seat to its highest position. Remove the chassis cover. Remove the positive pole from one battery. Block up the appropriate side of the wheelchair. Remove the wheel. See Changing the drive wheel, page 10.
  • Page 16 Changing the drive motor Detach the brake release wire from the magnetic brake. Brake release wire Remove the three screws which hold the motor. 10. Turn the motor sideways so that the wheel axle turns freely. Pull the motor straight forwards.

  • Page 17: Fitting

    Changing the drive motor Fitting If a new motor is to be fitted, the magnetic brake must be moved from the old motor. See Fitting a magnetic brake, page 13. Fit the spacer and lift the motor into place. Turn it a little so that the wheel axle can turn freely without being obstructed by the chassis.
  • Page 18 Changing the drive motor Attach the electrical connections for the motor and magnetic brake. NB. Ensure that the contacts are fully interlocking.n Magnetic brake contact Motor contact Fit the fuse holder with the two screws. Fit the wheel. See page 10. Remove the blocks.

  • Page 19: Changing The Carbon-Brush In The Drive Motor

    Changing the carbon-brush in the drive motor Changing the carbon-brush in the drive motor Removal Remove the drive motor. See page 15. Remove the motor's cables from the coupling box. Remove the magnetic brake and the mounting plate. Mark the stator's position against both ends with a small mark before loosening the nuts.

  • Page 20: Fitting The Carbon-Brush

    Changing the carbon-brush in the drive motor Fitting Fit a new carbon-brush using the fitting ring provided with the new brush holder. Ensure that you turn the cables in the same direction as the outgoing shaft of the gear. Fit the end with two nuts. Marking Remember the wave washer between the bearing and the end.

  • Page 21: Changing The Seat Lift

    Changing the seat lift Changing the seat lift Removal Raise the seat lift to its highest position (use the crank provided for chairs without a seat lift). Remove the cover. Cut off the cable ties located on the seat lift and under the seat.

  • Page 22: Fitting

    Changing the seat lift Fitting Lift and replace the seat lift. Replace the yoke and secure the seat lift by tightening the four nuts. The screws must be tightened with 24 Nm. Attach the contacts to the seat lift. Lift and replace the seat and secure it by tightening the four screws.

  • Page 23: Changing The Seat Lift Motor

    Changing the seat lift motor Changing the seat lift motor Removal Remove the seat lift as shown on page 21. Disconnect the seat lift cables from the motor. Unscrew the three screws which hold the motor and remove the motor. Fitting Fit the new motor and secure it by tightening the three screws.

  • Page 24: Seat Lift Belt

    Changing the seat lift belt Changing the seat lift belt Remove the seat lift. See page 21. Loosen the four screws which hold the seat lift motor. Move the motor sideways so that the belt becomes slack. Remove the belt first from the motor and then from the cog wheel on the seat lift screw.

  • Page 25: Changing The Control Unit

    Changing the control unit Changing the control unit Removal Raise the seat to its highest position. Remove the chassis cover. Remove the poles from the battery. Start with the positive poles. Detach the two cable connections on the right side. Detach the three cable connections on the left side.
  • Page 26 Changing the control unit Cut off the cable ties which hold the cables in the chassis and seat. If the seat has a seat lift or seat inclination, the cable ties which hold the cables for the button box and the control unit must be cut off.

  • Page 27: Fitting

    Changing the control unit Fitting Place the button box holder on the new control unit. Screw the button box in place with the two screws. Fit the control unit on the panel holder with the three screws. Fit the centre screw first and then adjust the control unit to the angle required.
  • Page 28 Changing the control unit Fasten the cables under the chair and around the base of the seat lift using cable ties. NB! The radius of the curve of the cable must be at least 80 mm when the seat lift is in its highest position.

  • Page 29: Troubleshooting

    Battery indicator - Battery indicator flashes fast. Battery indicator A fault has occurred and the wheelchair will not The battery indicator indicates the status of the work. The number of flashing lights indicates the wheelchair. nature of the fault. - Note the number of flashing lights. - Battery indicator lights permanently - Switch off the wheelchair.

  • Page 30: Fault Codes

    CABEL SWITCHBOX 5547 CABEL FUSE KIT 8391-1 MEMBRANSWITCH ACTUATOR CONTROLLER 5954-10 MEMBRANSWITCH 6061-3 Wiring diagram...
  • Page 31 Permobil INC. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256...

Table of Contents