Related Manuals for Bosch DINION 7100i IR
Summary of Contents for Bosch DINION 7100i IR
- Page 1 DINION 7100i IR NBE‑7702‑ALX | NBE‑7702‑ALXT | NBE‑7703‑ALX | NBE‑7703‑ALXT | NBE‑7704‑AL | NBE‑7704‑ALT | NBE‑7704‑ALX Installation manual...
-
Page 3: Table Of Contents
DINION 7100i IR Table of contents | en Table of contents Safety Safety message explanation Safety precautions Important safety instructions Notices Short information System overview Product description Intended use Preparing for installation Unpacking Parts included Preparation In-box configuration Wiring Network and PoE power - RJ45 4.5.1... - Page 4 | Table of contents DINION 7100i IR Disposal 10.2 2023-08 | V02 | DOC Bosch Security Systems B.V. Installation manual...
-
Page 5: Safety
DINION 7100i IR Safety | en Safety Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the device. Safety message explanation In this manual, the following symbols and notations are used to draw attention to special... -
Page 6: Notices
Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. - Page 7 Responsible party Bosch Security Systems Inc 130 Perinton Parkway 14450 Fairport, NY, USA For more information please contact the nearest Bosch Security Systems location or visit: www.boschsecurity.us For use in China: CHINA ROHS DISCLOSURE TABLE Fixed cameras with lens Hazardous substance table according to SJ/T 11364-2014...
- Page 8 Security advisories, that is a list of identified vulnerabilities and proposed solutions: https://www.boschsecurity.com/xc/en/support/product-security/security- advisories.html Bosch assumes no liability whatsoever for any damage caused by operating its products with outdated software components. Old electrical and electronic equipment This product and/or battery must be disposed of separately from household waste.
-
Page 9: Short Information
Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between this manual and the product described. Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. -
Page 10: System Overview
All DINION 7100i IR cameras have a 3-step concept for simple installation. With the combination of the robust housing, exceptional image quality and the powerful video analytics, the DINION 7100i IR cameras are the ideal choice for the most demanding outdoor applications, including traffic monitoring, critical infrastructure, and perimeter security. -
Page 11: Preparing For Installation
This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all parts are included. If any items are missing, notify your Bosch Security Systems sales or customer service representative. -
Page 12: Preparation
– Screwdriver for TR20 bit, or use a torque wrench TR20 hex key. – microSD card (optional) Note: Bosch recommends the use of industrial microSD cards with health monitoring. – Wireless installation dongle for wireless commissioning (optional). In-box configuration In-box configuration of the camera can be done via a wired connection with the camera still inside the box. -
Page 13: Network And Poe Power - Rj45
DINION 7100i IR Preparing for installation | en 5 RJ45 network connector 6 Cable holder / grounding point for punch down connector 7 Safety plunger 8 PCBA camera connector Notice! Make sure to pull and hold the safety plunger when removing the camera. - Page 14 | Preparing for installation DINION 7100i IR Power-over-Ethernet (PoE) can be connected at the same time as a 24V AC / 12-26V DC power supply. If auxiliary power (24V AC / 12-26V DC) and PoE is applied simultaneously, the camera draws its power from PoE by default, and seamlessly switches to auxiliary input if PoE power fails.
-
Page 15: 10-Pin I/O Connector
DINION 7100i IR Preparing for installation | en 4.5.3 10-pin I/O connector Connection +12V OUT ALARM IN 2 ALARM IN 1 ALARM OUT ALARM OUT AUDIO OUT AUDIO IN 12V DC power output The 12V DC output can be enabled/disabled via the web interface, and controlled via the Alarm Task Editor. -
Page 16: Grounding
Grounding provides improved surge protection (up to 1 kV, 1 kA to ground (8/20 µs pulse)). The grounding wire is not included in the box. Bosch recommends the use of a grounding wire with a ring terminal. The ring terminal must not have a thickness greater than 2 mm (0.01 in.). -
Page 17: Hardware Installation
DINION 7100i IR Hardware installation | en Hardware installation Installation overview The installation of the camera follows these steps: Installing the mounting plate, page 17 Installing the camera base, page 18 Installing the camera, page 20 Installation options The camera can cover various mounting options when combined with the available accessories. -
Page 18: Installing The Camera Base
| Hardware installation DINION 7100i IR Mark the positions of the screw holes on the surface. Note: For standard installation, use the mounting holes marked with a B on the mounting plate. For a different installation, for example for an installation on a surveillance cabinet, use different mounting holes. - Page 19 DINION 7100i IR Hardware installation | en Slightly rotate the camera base in a clockwise motion until it makes a clicking sound. Note: Make sure that the camera base is secured. Insert a grommet to protect the cable: – For an RJ45 network cable, insert the IP66 grommet tightly around the cable.
-
Page 20: Installing The Camera
| Hardware installation DINION 7100i IR Installing the camera 5.3.1 Installation steps Carefully align the camera with the camera base. Connect the safety cable on the camera to the safety hook located on the right side of the camera base. - Page 21 DINION 7100i IR Hardware installation | en To adjust the position of the camera, unlock the locking ring by rotating it counter- clockwise. Once the position is set: Lock the device manually by rotating the locking ring clockwise. To fully secure the device, lock it with the locking screw (4 Nm).
-
Page 22: Other Optional Accessories
5.4.1 Inserting microSD card(s) and Wireless installation dongle Notice! Use microSD cards for maximum reliability. Bosch does not recommend the use of SD to microSD adapters. Locate the rear panel on the back of the device. Fully untighten one screw. -
Page 23: Illuminator Module/Kit
DINION 7100i IR Hardware installation | en Insert microSD card(s) and/or a Wireless installation dongle for wireless commissioning. Once the wireless commissioning process is completed, remove the Wireless installation dongle. Place the rear panel back. Tighten both rear panel screws (2 Nm). - Page 24 | Hardware installation DINION 7100i IR The illuminator module/kit provides covert or semi-covert lighting for wide range outdoor surveillance applications. 5.4.2.1 Illuminator module invisible light Installation steps Notice! Make sure that the camera is on top of a flat surface and disconnected from a power source before starting this procedure.
- Page 25 DINION 7100i IR Hardware installation | en Take the IR module of the illuminator out of its packaging. Attach the same circular lens support to the new IR module with 2 screws. Use 2 screws to attach the IR module to the device.
-
Page 26: Polarizing Filter Kit
In such events caused by sunlight, white surfaces, vehicles, mirrors, etc., the polarizing filter offers optimal image quality. The polarizing filter kit is available for DINION 7100i IR tele variants only. Installation steps Remove the 4 screws from the front window of the device. -
Page 27: Surveillance Cabinet (Fiber Optics) Installation
The surveillance cabinet provides additional room to install the fiber optics module VG4- SFPSCKT. Bosch surveillance cabinets are designed to meet the power and electrical safety requirements for cameras used in outdoor security applications. The surveillance cabinets provide a power supply for situations without PoE. - Page 28 | Hardware installation DINION 7100i IR The following table includes detailed information on the different status LED functions: Status LED Meaning Solid red Booting Flashing red Resetting Solid green Working, but stream is not being watched or recorded Flashing green Stream is being watched and/or recorded Disable the status LED in the camera settings, if necessary.
-
Page 29: Commissioning
DINION 7100i IR Commissioning | en Commissioning The DINION 7100i offers commissioning functionalities to access the device for installation, configuration and test: – In-box configuration via an RJ45 patch cable connection to enable wired commissioning – Configuration using a Wireless installation dongle for local commissioning The commissioning can be done locally by connecting the camera via one of the following: –... -
Page 30: Connection Via The Web Browser
| Connection via the web browser DINION 7100i IR Connection via the web browser A computer with a web browser (Google Chrome, Microsoft Edge, or Mozilla Firefox) is used to receive live images, control the unit, and replay stored sequences. The unit is configured over the network using the browser. - Page 31 DINION 7100i IR Connection via the web browser | en Enter the user name (“service”) and a password in the appropriate fields. Refer to the section User Management for more information. After a service-level password is set for the device, the device displays a dialog box that prompts users to enter the user name (“service”) and the service-level password every time...
-
Page 32: Troubleshooting
| Troubleshooting DINION 7100i IR Troubleshooting Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution Unit does not operate. Power failure. Make sure that the power supply is working properly. -
Page 33: Testing The Network Connection
Customer service If a fault cannot be resolved, please contact your supplier or system integrator, or go directly to Bosch Security Systems Customer Service. The version numbers of the internal firmware can be viewed on a service page. Please note this information before contacting Customer Service. -
Page 34: Maintenance
| Maintenance DINION 7100i IR Maintenance Cleaning Front window cleaning Caution! Do not touch the front window. It is important to keep the front window clean to ensure optimum performance. Dust, grease, or fingerprints should be removed from the front window surface –... - Page 35 DINION 7100i IR Maintenance | en Notice! Only reset the device when connected and powered up. Place the rear panel back. Tighten both rear panel screws (2 Nm). Bosch Security Systems B.V. 2023-08 | V02 | DOC Installation manual...
-
Page 36: Decommissioning Transfer
– Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2023-08 | V02 | DOC Bosch Security Systems B.V. Installation manual... - Page 37 DINION 7100i IR Decommissioning | Bosch Security Systems B.V. 2023-08 | V02 | DOC Installation manual...
- Page 38 | Decommissioning DINION 7100i IR 2023-08 | V02 | DOC Bosch Security Systems B.V. Installation manual...
- Page 40 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2023 Building solutions for a better life. 202309211450...