Table of Contents
Advertisement
6.
MENU SETTINGS
6.1 Access the settings menu
1. Press the "
" button (C3) to enter the menu;
2. Scroll through the menu items by pressing
until the required items is displayed;
3. Press the menu item you want to select.
6.2 Exit the menu
When you have made the adjustments, press
until you are back on the homepage.
6.3
Rinse
Use this function to deliver hot water from the coffee spouts
(A9) and hot water spout (D6), if inserted, to clean and heat the
appliance's internal circuit.
1. Place a container with a minimum capacity of 100ml under
the coffee and hot water spouts (fig. 8).
2. A few seconds after the "RINSING" item has been selected,
hot water is delivered first from the coffee spouts and then
from the hot water spout (if inserted) which cleans and
heats the appliance's internal circuit (fig. 7).
3. To stop rinsing, press
stop automatically.
Please note!
•
If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
•
After cleaning, it is normal for the grounds container (A11)
to contain water.
6.4 Descaling
For instructions on descaling, see section "14. Descaling".
6.5 Water filter
For instructions on how to install the filter (D7), see section "16.
Water softener filter".
6.6 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage and each
profile.
1. Once in the settings menu, press "DRINK SETTINGS". The
values for the first beverage appear on the display;
2. The values are displayed on vertical bars. The default value
is indicated by the
highlighted by the solid part of the vertical bar;
3. To go back to the settings menu, press
scroll and display the beverages, press
4. To reset the default values for the beverage displayed,
press
;
or wait for rinsing to
symbol, while the current value is
5. "CONFIRM RESET?": to confirm, press
cancel, press
6. "VALORI FABBRICA""IMPOSTATI": press
The beverage has been reset to the default values. Proceed with
the other beverages or go back to the homepage by pressing
twice.
Please note!
To change the beverages in another profile, go back to the
homepage, select the required profile and repeat the procedure.
6.7 Auto-off (standby)
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press "AUTO-OFF";
2. Select the required time interval by pressing the selection
arrows
3. To confirm, press
Auto-off is programmed.
6.8
Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
1. Press "ENERGY SAVING" to disable (
ble (
) the function;
The corresponding symbol (B2) appears on the top bar of the
homepage to indicate that the function has been enabled.
Please note:
If "Energy Saving" is active, you may have to wait a few seconds
before delivery.
6.9 Coffee temperature
To modify the temperature of the water used to make the coffee,
proceed as follows:
"COFFEE TEMPERATURE"
1. Press
appear on the display (B1) (the current value is underlined);
2. Press the value you want to set (LOW, MEDIUM, HIGH,
MAXIMUM).
6.10 Water hardness
For instructions on setting water hardness, see section "15. Set-
ting water hardness".
. To
6.11 Set language
;
To modify the language of the display, proceed as follows:
"
1. Press
SET LANGUAGE";
9
);
(increase) or
(decrease);
.
. The selectable values
(to
.
) or ena-
Advertisement
Table of Contents
Troubleshooting
