Advertisement
MENU
FEATURE
341
enable Pin
access
342
Set PIN Access
Code
350
Fan Mode
Enable
360
System Mode
Enable
380
Minimum Deadband
Adjustment
390
Pre-Occupancy
Purge
395
Maximum Override
0=Time until next
Time Limit
400
Cycles Per Hour
(CPH)
Cooling Stage 1
410
Cycles Per Hour
(CPH)
Cooling Stage 2
420
Cycles Per Hour
(CPH)
Heating Stage 1
430
Cycles Per Hour
(CPH)
Heating Stage 2
450
Cycles Per Hour
Heating Stage 3
460
Heat Recovery Rate
470
Cool Recovery Rate
480
Minimum Off Time
490
Humidity Control
Enable
(Select models only)
500
Programmable/
Intermittent Fan
501
Intermittent Fan On
Time
502
Intermittent Fan Off
Time
© COPYRIGHT 2014 PECO ASTRONICS. ALL RIGHTS RESERVED.
OPTIONS
STD. DEFAULT
0,1
0
000-999
000
1-3
3
0-3
1
3-10°F, 1.5-5°C
3°F
0-3 hours
0 hours
3
event; or
1-4 hours
0-6 CPH
0 CPH
0-6 CPH
0 CPH
0-12 CPH
0 CPH
0-12 CPH
0 CPH
0-12 CPH
0 CPH
0-18°F/Hr
0°F/Hr
0-10°C/Hr
0-18°F/Hr
0°F/Hr
0-10°C/Hr
1-10 minutes
4 minutes
0-2
0
1-60 minutes
5 minutes
0-60 minutes
25 minutes
DESCRIPTION / COMMENTS
Applies a 3 digit access code to enter Service Menu 342
0 =
Disable,
1 =
Enable
Choose a 3-digit code.
1 =
ON: Fan is turned on regardless of demand.
2 =
Auto: Fan is turned on according to heating or cooling demand.
3 =
ON or Auto: Allows occupant to select either 1 or 2 above.
Allows ability to determine which system modes the occupant can select.
0 =
OFF, Auto (0 is NOT valid for following configurations: Heat Only; Cool Only.)
1 =
OFF, Heat, Cool, Auto
2 =
OFF, Heat, Cool
3 =
Heat, Cool, Auto
Select a changeover deadband value to prevent short cycling between heating and cooling
modes.
The value is adjustable to meet various HVAC system requirements.
Select to energize fan for selected number of hours (0-3) prior to all occupied events.
Restricts the duration that a temporary hold can be set. The temporary hold is limited by the
maximum amount of time as defined in this Service Menu.
0 =
Remainder of time until the next scheduled event.
1 =
1 Hour
2 =
2 Hours
3 =
3 Hours
4 =
4 Hours
Defines the number of cycles per hour for cooling (Stage 1). Select 0 to enable ON-OFF
control for Stage 1 cooling.
Defines the number of cycles per hour for cooling (Stage 2). Select 0 to enable ON-OFF
control for Stage 2 cooling.
Defines the number of cycles per hour for heating (Stage 1). Select 0 to enable ON-OFF
control for Stage 1 heating.
Defines the number of cycles per hour for heating (Stage 2). Select 0 to enable ON-OFF
control for Stage 2 heating.
Defines the number of cycles per hour for heating. Select 0 to enable ON-OFF control for
Heating Stage 3.
Defines the rate at which the device achieves the heat comfort setpoint. Select 0 to disable
ramp recovery.
Defines the rate at which the device achieves the cool comfort setpoint. Select 0 to disable
ramp recovery.
Sets the minimum off time for both the heat and cool output.
Selects how humidity will be controlled. When dehumidify control is enabled, the Y2
terminal becomes dehumidify.
0 =
Disabled
1 = Dehumidify Control
0 =
Disable
1 =
Programmable Fan: Fan operates continuously in occupied periods or with demand in
unoccupied periods.
2 =
Intermittent Fan: Fan operates based on the on and off times set in menus 501 and
502.
Defines the on time for the Intermittent Fan.
Defines the off time for the Intermittent Fan. Select 0 for continuous fan.
3
P/N 70930 3220-2322 REV 00
Advertisement
