Advertisement
TIME display--When
the manual mode or an
• iFIT.com program is
selected, this display
shows the elapsed time.
When a pemonal trainer
program is selected, this display shows both the
time remaining in {he program and the time re-
maining in the current segment of the program.
The display will alternate between one number and
the other every seven seconds.
CALS/FAT CALSI
PULSE display--This
display shows the ap-
proximate numbers of
ca/Dries and fat ca/odes
you have burned (see
FAT BURNING on page
22). Every seven seconds, the display will change
from one number to the other, as shown by the ar-
rows in the display. This display will also show
your heart rate when the pulse sensor is used (see
step 6 on this page).
SPEED/MIN-MILE
display--This
display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
L
i
SPEED
MINI MILE (kin)
mile). Every seven seconds, the display will
change from one number to the other, as shown
by the arrows in the display.
Note: The SPEED/MIN-MILE
display can show
speed in either miles per hour or kilometers per
hour. To find which unit of measurement
is se-
.
lected, hold down the STOP button while inserting
the key into the console.
An "E" for English miles
or an "M" for metric kilo-
C'
meters will appear in the
12
display. Press the
SPEEDMIN/MILE (kin)
SPEED _ button to
change the unit of mea-
surement. When the desired unit of measurement
is selected, remove and then reinsert the key.
Note: To reset the displays, press the STOP but-
ton, remove the key, and then reinsert the key.
I
r_
Measure your heart rate, if desired.
Stand on the
foot rails and
Sensors
place your
hands on the
metal contacts
on the pulse bar.
Your palms
must be resting
on the upper
contacts, and
_t_
PULSE
your fingers must
be touching the
"
123
lower contacts--
CALS. FAT ¢ALG.
avo|d moving
your hands.
When your pulse is detected, the heart-shaped in-
dicator in the CALS/FAT CALS/PULSE display will
flash steadily and a sedes of dashes (- -) will ap-
pear. After a few seconds, your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
B
When you are finished exercising, remove the
key,
Step onto the foot rails, press the STOP button,
and adjust the incline of the treadmill to the lowest
level. The incline must be at the lowest level
when the treadmill Is raised to the storage po-
sition or the treadmill will be damaged.
Next,
remove the key from the console and put the key
in a secure place. Note." If the displays and vari-
ous indicators
on the console remain lit after
the key is removed, the console is in the
"demo" mode. Refer to page 18 and turn off the
demo mode.
When you are finished using the treadmill, move
the on/oft switch near the power cord to the off
position.
11
Advertisement
Need help?
Do you have a question about the 835QT and is the answer not in the manual?
Questions and answers
the reset switch is in the proper position but still no power
The Pro-Form 835QT may have no power despite the reset switch being in the proper position due to several possible reasons:
1. The power cord may not be plugged into a surge suppressor, or the surge suppressor may not be plugged into a properly grounded outlet.
2. The surge suppressor may not meet the required specifications (UL 1449 listed, 400V suppressed voltage rating, 450J minimum surge dissipation, 120V AC, 15A).
3. The treadmill may be plugged into a GFCI-equipped outlet, which is incompatible with the treadmill.
4. The key may not be fully inserted into the console.
5. The on/off switch near the power cord may not be in the "on" position.
6. The circuit breaker on the treadmill frame may have tripped and needs resetting.
Check these factors to restore power to the treadmill.
This answer is automatically generated