Electrical Requirements - Maytag MAT20CSTGW Instructions Manual

Electrical Requirements

WARNING
Electrical Shock Hazard
Plug into an earthed socket outlet.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
A 220–240 V, 50 Hz, fused electrical supply is required.
■
A time-delay 10–16 A fuse or circuit breaker is
recommended.
A detachable 3 conductor, 250 V, 10 A, 1.0 mm
■
(18 AWG) minimum, power supply cord, 1,800 mm (6 ft) long
(minimum), with one end terminated with an
IEC 60320-1 C13 connector, the other end terminated in a
3 prong, earthing-type plug meeting the local, national,
and/or regional approval authority/safety agency standards is
required. Approved Maytag power supply cords are available
for order for specific regions per the Power Cord Selection
table.
To minimize possible shock hazard, the cord must be
■
plugged into a mating, 3 prong, earthing-type outlet, earthed
in accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly earthed
outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is
■
recommended that a qualified electrician determine that
the earth path is adequate.
If the supply cord is damaged, it must be replaced by a
■
special cord or assembly available from the manufacturer or
its service agent.
Do not earth to a gas pipe.
■
Check with a qualified electrician if you are not sure
■
the washer is properly earthed.
Do not have a fuse in the neutral or earth circuit.
■
Only a Maytag service person, qualified electrician, or
■
similarly qualified person shall replace a power cord or
perform service on the electrical power supply in accordance
with these instructions and local codes and regulations.
This product is shipped with the AS/NZS 3112 power
■
cord installed. Additional power cords are supplied with
the product. Refer to the Power Cord Selection table to
determine the power cord required for your region, or if
needed, to order the appropriate approved Maytag power
supply cord .
10
This washer must be earthed. In the event of a malfunction
or breakdown, earthing will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The
plug must be plugged into an appropriate outlet that is
properly installed and earthed in accordance with all local
codes and ordinances.
WARNING:
earthing conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly earthed.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
NOTE: Electrical safety standards: The manufacturer has
chosen compliance with IEC/EN.60335 standards as the most
appropriate for this product.
Sound Pressure Level, LpA: 58 dbA (uncertainty,
■
kPa: +/-3.6 dbA)
Part Number
W11318406
(fused 13A)
(Included in
2
product)
W11318407
(Included in
product)
W11318408
(Installed on
product as
shipped)
* - https://www.ice.ch/worldplugs/
EARTHING INSTRUCTIONS
Improper connection of the equipment-
POWER CORD SELECTION
IEC Plug Type*
G
E,F Schuko
(CEE 7/7)
I
Intended
Counties/Region
United Kingdom,
Ireland, Cyprus,
Malaysia, Malta,
Nigeria, Singapore,
Hong kong, Saudi
Arabia, UAE, GCC
states, others (BS1363)
EU, Belgium, Chile,
Egypt, France,
Indonesia, Jordan,
Rep.of Korea,
Paraguay, Russia,
Thailand, Uruguay,
Ukraine, Vietnam,
others
Australia, China, New
Zealand, Papua New
Guinea (AS/NZS 3112)