Related Manuals for Monster MT-SB212DA
Summary of Contents for Monster MT-SB212DA
- Page 1 2.1.2 Channel Dolby Atmos Soundbar with Wireless Subwoofer MODEL: MT-SB212DA User Manual...
-
Page 2: Welcome
Welcome Premium connectivity that fuels modern lifestyle and empowers innovation. A better everyday experience through amazing products. The user manual will provide everything you need to know about using your new product. All our products are produced and tested to stringent standards of performance and safety, and are pleased to provide a 2 Year Warranty with your purchase. -
Page 3: Table Of Contents
Contents Welcome Product Overview Controls and Connections Remote Control Operation Bluetooth ® Troubleshooting Specifications Compliance and Responsible Disposal... -
Page 4: Product Overview
Product Overview What’s in the box: A. 2.1.2 Channel Dolby Atmos Soundbar B. Wireless Subwoofer C. Remote Control D. AAA Batteries (2) E. AC Power Cord F. Optical Cable G. Wall Mount Kit H. User Manual I. Warranty Certificate J. General Safety Warnings 4 | PRODUCT OVERVIEW... - Page 5 Wall Mount Kit The illustration below shows the contents of the wall mount kit. These are the parts you will need when wall mounting the soundbar. Some parts are not shown at the same scale. 1. Plastic anchor (4) 2. Long screw (4) 3.
- Page 6 Installation - Free Standing This soundbar can sit free-standing on a surface, or it can be mounted to a wall. Place on a secure, flat surface. Make sure the soundbar is standing on its rubber pads (on the left and right sides of the soundbar) and no other area of the bottom of the soundbar is touching the surface.
- Page 7 Installation - Wall Mounted Wall mounting instructions are on the following pages. • Wall mounted installation must be carried out by qualified personnel only. Incorrect assembly can result in severe personal injury and property damage! If you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing, which may be hidden inside or behind the wall.
- Page 8 Wall Mounting Instructions Use a pencil to make drill hole marks on the wall for the anchors. Make sure the marks are level before drilling. Use a 6mm bit and power drill (not supplied) to drill holes on the marks. Insert plastic anchors into the holes and push in until they are flush with the wall.
- Page 9 Place the sponge pads on top of the mounting plates, with the holes aligned as pictured. Insert screws through the holes and tighten. Mount the soundbar onto the mounting plates. Note: there will be a gap between the soundbar and the mounting plate on the wall.
- Page 10 Connect to Power Make sure the power switch is switched off at the power outlet until you have finished connecting your cables. Rear view Don't forget to plug in the soundbar to the power outlet. Leave the power switched off until installation is finished.
-
Page 11: Controls And Connections
Controls and Connections Get to know your Soundbar LED display Remote control sensor Front view Buttons on the Soundbar Top view POWER: press to turn the soundbar on/off. 2. - button: press to decrease volume level. 3. + button: press to increase volume level. : press repeatedly to change between input sources. - Page 12 Ports on the Soundbar Play your stored media files (supported file codecs and STORAGE extensions may vary). Connect an optical cable (included) to the OPTICAL OPTICAL SOUND OUT socket of your device (e.g. TV, DVD player) and the OPTICAL socket on the soundbar. Use a 3.5mm audio cable (not included) to connect the AUX IN SOUND...
- Page 13 Connect the AC power cord to the AC IN connector on the AC IN POWER soundbar and the other end to a power source. Rear Ports on the Soundbar HDMI (ARC) To use the ARC function, make sure the soundbar's TO TV (ARC) socket is connected via HDMI cable (not included) to the HDMI (ARC) socket of your ARC compliant TV.
- Page 14 Wireless Subwoofer Rear Power cord - connect to power the subwoofer. 2. LED Indicator - flashes blue slowly when searching to pair with the soundbar. Flashes blue quickly when pairing with the soundbar. Once pairing is successful, lights up blue. When on standby, lights up red.
- Page 15 Pairing the subwoofer to the soundbar manually Connect both the soundbar and subwoofer to the AC power at the same time. 2. The LED indicator on the subwoofer will flash blue slowly. Press and hold the PAIR button to enter pairing mode, the LED indicator will flash blue quickly.
-
Page 16: Remote Control
Remote Control Setup Insert two AAA size batteries according to the polarity markings (+ / -) inside the compartment. Make sure the batteries are correctly aligned and AAA size properly pushed into place. batteries included Precautions When Using Batteries • Do not use old and new batteries together. - Page 17 Using the Remote Control To use the remote, point it towards the remote sensor at the front of the soundbar. The remote will not operate if its path is blocked. The remote has a range of up to about 6 metres from the soundbar at an angle of up to 30 degrees to either side of the sensor, as illustrated below.
- Page 18 Remote Overview MUTE: Press to mute. Press again POWER: Switch the soundbar to MUTE MUTE to unmute On or Standby INPUT : Press to change between P P AIR INPU INPUT T PAIR: Press and hold to connect or input modes disconnect the Bluetooth device VOL+ VOL+...
-
Page 19: Operation
Operation General Operation Input Modes Function Action Mode LED display Press the button on the side of the soundbar, or press the Turn the soundbar (POWER) button on the remote Standby control to switch the soundbar HDMI (ARC) Press and hold the button on the side of the soundbar, or Turn the soundbar... - Page 20 Dolby Atmos Note: Your TV must support Dolby Atmos. If your TV does not support Dolby Atmos, you must connect a Dolby Atmos supported media player via the HDMI ports. You must use a HDMI 2.0 cable to connect. • Ensure that “No encoding”...
-
Page 21: Bluetooth
® pairing mode automatically. set it to search for compatible devices. Select the speaker name: 'MT-SB212DA' from the list of found devices. If a mobile phone on which you are playing Note: Only one playback soundbar can be music receives a call, the music will be interrupted. - Page 22 Bluetooth Playback ® Function Action Increase the Volume Press the + button on the soundbar or VOL + on the remote. Decrease the Volume Press the - button on the soundbar or VOL - on the remote. Play/Pause Press /RESET on the remote. Skip/Rewind Press on the remote to skip/rewind tracks.
-
Page 23: Troubleshooting
Troubleshooting If you encounter any problems with your product, please check this list of possible issues for a solution. If you don’t find a solution here, contact After Sales Support on 1300 886 649. Problem Solution • Ensure that the power is properly connected. No power •... - Page 24 Problem Solution • The unit may not be able to decode all digital audio formats from the input source. In this case, the unit will mute. This is NOT a defect. Ensure that the audio setting of the external device is set to PCM or Dolby Digital. No sound in HDMI 1 and/or 2 •...
- Page 25 • Please pair the subwoofer manually. For Technical and Warranty Support 1300 886 649 monster@tempo.org monsterproducts.com.au Distributed by Tempo (Aust) Pty Ltd, PO Box 132, Frenchs Forest NSW 1640 TROUBLESHOOTING | 25...
-
Page 26: Specifications
Soundbar: 2 x 30W + 2 x 20W Power output (RMS) Subwoofer: 80W Bluetooth pairing operation range Up to 10 metres Bluetooth pairing name MT-SB212DA Bluetooth pairing password 0000 Bluetooth version Remote control operation range Up to 10 metres 960 x 81 x 106mm (Soundbar) -
Page 27: Compliance And Responsible Disposal
Compliance and Responsible Disposal Packaging Compliance The packaging of your product has been This product complies with the Australian selected from environmentally friendly Safety Standard AS/NZS 62368.1 to ensure materials and can usually be recycled. Please the safety of the product. ensure these are disposed of correctly.