Welcome Premium connectivity that fuels modern lifestyle and empowers innovation. A better everyday experience through amazing products. The user manual will provide everything you need to know about using your new product. All our products are produced and tested to stringent standards of performance and safety, and are pleased to provide a 2 Year Warranty with your purchase.
Contents Welcome Product Overview Controls and Connections Remote Control Operation Bluetooth ® Troubleshooting Specifications Compliance and Responsible Disposal...
Product Overview What’s in the box: A. 5.1.2 Channel Soundbar B. Wired Subwoofer C. Wireless Surround Speakers (2) D. Remote Control E. AAA Batteries (2) F. AC Power Cord G. Optical Cable H. Wall Mount Kit I. User Manual J. Warranty Certificate K.
Page 5
Wall Mount Kit The illustration below shows the contents of the wall mount kit. These are the parts you will need when wall mounting the soundbar and/or wireless surround speakers. Some parts are not shown at the same scale. 1. Plastic anchor (8) 4.
Page 6
Installation - Free Standing This soundbar can sit free-standing on a surface, or it can be mounted to a wall. Place on a secure, flat surface. Make sure the soundbar is standing on its rubber pads (on the left and right sides of the soundbar) and no other area of the bottom of the soundbar is touching the surface.
Page 7
Installation - Wall Mounted Wall mounting instructions are on the following pages. • Wall mounted installation must be carried out by qualified personnel only. Incorrect assembly can result in severe personal injury and property damage! If you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing, which may be hidden inside or behind the wall.
Page 8
Wall Mounting Instructions (Soundbar) Use a pencil to make drill hole marks on the wall for the anchors. Make sure the marks are level before drilling. Use a 6mm bit and power drill (not supplied) to drill holes on the marks. Insert plastic anchors into the holes and push in until they are flush with the wall.
Page 9
Place the sponge pads on top of the mounting plates, with the holes aligned as pictured. Insert screws through the holes and tighten. Mount the soundbar onto the mounting plates. Note: there will be a gap between the soundbar and the mounting plate on the wall.
Page 10
Wall Mounting Instructions (Surround Speakers) Use a pencil to make drill hole marks on the wall for the plastic anchors at the desired mounting location. Make sure the marks are level before drilling. Use a 6mm bit and power drill (not supplied) to drill holes on the marks.
Page 11
Mount the surround speakers on top of the mounting bracket. Insert a wing nut through the bottom of each bracket to the surround speaker and ensure they are secure. PRODUCT OVERVIEW | 11...
Page 12
Connect to Power Don't forget to plug in the soundbar to the power outlet. Leave the power switched off Make sure the power switch is switched off until installation is finished. at the power outlet until you have finished connecting your cables. Rear view Ensure to use the supplied AC adaptors when...
Controls and Connections Get to know your Soundbar LED display Remote control sensor Front view Buttons on the Soundbar Top view POWER: press to turn the soundbar on/off. 2. - button: press to decrease volume level. 3. + button: press to increase volume level. : press repeatedly to change between input sources.
Page 14
Ports on the Soundbar WOOFER SOUND Connect to the wired subwoofer with the supplied cable. PORT Connect an optical cable (included) to the OPTICAL OPTICAL SOUND OUT socket of your device (e.g. TV, DVD player) and the OPTICAL socket on the soundbar. Use a 3.5mm audio cable (not included) to connect the AUX IN SOUND...
Page 15
Connect the AC power cord to the AC IN connector on the AC IN POWER soundbar and the other end to a power source. Rear Ports on the Soundbar HDMI (ARC) To use the ARC function, make sure the soundbar's TO TV (ARC) socket is connected via HDMI cable (not included) to the HDMI (ARC) socket of your ARC compliant TV.
Page 16
Wireless Subwoofer Rear Illustration for reference only. 1. Connection port - use the cable at the woofer to connect to the woofer port on the soundbar. Sound will now be played through the subwoofer. For best sound experience, place the subwoofer on the ground near the soundbar.
Page 17
Wireless Surround Speakers or or Master speaker Secondary Bottom (Master Rear (Master speaker Speaker) Speaker) Master speaker surround SL LED light : lights up when the master speaker’s surround sound is set to left. 2. Secondary speaker surround SL or SL out : connect the secondary speaker input. 3.
Page 18
Pairing the wireless surround speakers with the soundbar Tap the button on the soundbar or press the button on the remote control to turn on the soundbar. 2. Using the supplied 24V, 1.25A AC adaptor, plug into the DC IN port and the other end of a mains socket to turn the rear speaker on, the connection indicator will flash blue.
Remote Control Setup Insert two AAA size batteries according to the polarity markings (+ / -) inside the compartment. Make sure the batteries are correctly aligned and AAA size properly pushed into place. batteries included Precautions When Using Batteries • Do not use old and new batteries together.
Page 20
Using the Remote Control To use the remote, point it towards the remote sensor at the front of the soundbar. The remote will not operate if its path is blocked. The remote has a range of up to about 6 metres from the soundbar at an angle of up to 30 degrees to either side of the sensor, as illustrated below.
Page 21
Remote Overview MUTE: Press to mute. Press again to unmute POWER: Switch the soundbar to On or Standby INPUT : Press to change between PAIR: Press and hold to connect or input modes disconnect the Bluetooth device DISPLAY : Turn LED display on/off RESET : Press and hold to reset to factory (only when the soundbar is turned default settings...
Operation General Operation Input Modes Function Action Mode LED display Press the button on the top of the soundbar, or press the Turn the soundbar (POWER) button on the remote Standby control to switch the soundbar HDMI (ARC) Press and hold the button on the top of the soundbar, or press Turn the soundbar...
Page 23
Dolby Atmos Note: Your TV must support Dolby Atmos. If your TV does not support Dolby Atmos, you must connect a Dolby Atmos supported media player via the HDMI ports. You must use a HDMI 2.0 cable to connect. • Ensure that “No encoding”...
® pairing mode automatically. set it to search for compatible devices. Select the speaker name: 'MT-SB512DA' from the list of found devices. If a mobile phone on which you are playing Note: Only one playback soundbar can be music receives a call, the music will be interrupted.
Page 25
Bluetooth Playback ® Function Action Increase the Volume Press the + button on the soundbar or VOL + on the remote. Decrease the Volume Press the - button on the soundbar or VOL - on the remote. Play/Pause Press on the remote. Skip/Rewind Press on the remote to skip/rewind tracks.
Troubleshooting If you encounter any problems with your product, please check this list of possible issues for a solution. If you don’t find a solution here, contact After Sales Support on 1300 886 649. Problem Solution • Ensure that the power is properly connected. No power •...
Page 27
Problem Solution No sound in USB mode • Make sure the USB drive is in FAT32 file format, and it’s no greater than 32GB; • Make sure the input source is set to ARC; the LED will display 'ARC'. • Make sure your TV or external device supports ARC function and connect the HDMI cable to the ARC port of the TV or external device.
Page 28
Connect the Woofer connection port on the subwoofer to the woofer port on the No sound from Subwoofer soundbar. For Technical and Warranty Support 1300 886 649 monster@tempo.org monsterproducts.com.au Distributed by Tempo (Aust) Pty Ltd, PO Box 132, Frenchs Forest NSW 1640 28 | TROUBLESHOOTING...
Rear Speakers: 2 x 20W both) Remote control 6 metres, 30 degrees (either operation range – side of sensor) distance, angle Bluetooth pairing operation range – Up to 10 metres distance Bluetooth pairing MT-SB512DA name Bluetooth pairing 0000 password Bluetooth version SPECIFICATIONS | 29...
Compliance and Responsible Disposal Packaging Compliance The packaging of your product has been This product complies with the Australian selected from environmentally friendly Safety Standard AS/NZS 62368.1 to ensure materials and can usually be recycled. Please the safety of the product. ensure these are disposed of correctly.