Harman Kardon AVR 435 Owner's Manual page 47

CONFIGURING THE REMOTE
changing devices or othercommon tasks. T hanks
to theremote's two linedisplay, it is easier thanever
for youto takeadvantage o f the power of macro
commands.
Recordinga Macro
Torecord a macrointotheremote's memory, follow
thesesteps:
1. Press andholdthe ProgramButton _ for
aboutthreeseconds whilethemessage shown
inFigure 24 appears inthe remote's LOD
Information Display0. Release t he button
whenthe redlightunderthe Set Button
appears.
2.The remote's M _Iirt MEMUmessage (Fig. 2 5),
willappear i nthe LCDdisplay andthe Set Button
willremainilluminated i n red.Press the •
NavigationButton _ throetimessothat
M_CROappears onthe bottomlineof the
LCDscreen, a sshowninFigure 47. Press the
Set Button _ to enterthe mainmacro
menubranch.
I M_I[_ ME!IU I
M _ C R 0 A
Figure 4 7
3.At the nextmenuscreen (Figure 4S)pressthe
Set Button _ to beginrecording a macro.
I M F_C F<0 I
F<E C 0 F<[I _ M _ ISF<0 A
Figure 4 8
4.Thenextdisplay screen(Figure 49) iswhereyou
select t he buttonthatwill beusedto recall t he
macro. T hechoices arethe PowerOn Button
or oneof thediscrete Macro Buttons_).
Press the •/T NavigationButton _ untilthe
nameof the button you wishto program the
macrointois shown.Forthisexample wewill
showhowto program a seriesof commands t hat
willautomatically be sentout everytimethe
Power buttonis pressed.
P O _IE R 0 il A
Figure 4 9
5.Thenextscreen thatappears (Figure 50) is where
youselect t he device for thefirstcommand that
will besentoutas pa_l o f the macro. P ress the
• /T NavigationButton _ until t he nameof
the device appears on the leftsideof the lower
linein theLCDdisplay. Forthisexample, the first
buttonwewantto havethe macro"press" i s the
Power Onbutton, s o theAVRdeviceisselected.
Press the Set Button _ whenthe desired
devicename appears to moveto the nextpro
gramming step.
I SELECT A [IE_EICE I A L/ P A
Figure 5 0
6. Thenextdisplay (Figure 51) iswhere you begin
entering the individual commands forthe macro,
inthe order youwishthemto betransmitted.
Remember thatwhenyouwant t o change devices,
youmustfirstpressthe InputSelectorsO
forthatbutton, a ndthenpresstheCommand o r
Function k ey.Since wewantto program a series
of eventsthatoccureachtimethe Power O n
button is pressed, p resstheAVRbutton. I nyour
specific macro, t hisis thefirstcommand button.
Figure 5 1
7. Thenextdisplay (Figure 52) andthesubsequent
screens arewheretheactual m acroprogramming
takesplace. Thewordsat the leftsideof thetop
lineofthe display showthebuttonthatis being
programmed (e.g.,the PowerOn Button _ or
oneof the MacroButtons _)) andtheindica
tionat the rightsideof the top lineshows the
number o f macrostepsavailable o f 20 possible
steps.Following t he instructions o nthe remote's
LCDscreen, p ressthefirstkeyyouwishto be
transmitted i n themacro. I nourexample, wefirst
wantthe AVR 435 to turnon,so thePower
Button _ shouldbe pressed.
I
P 0 IJE R
0 _I
8 _ / 2 8
[-:ELECT KE_
PRES_:
Figure 5 2
8. Oncethe firstcommand buttonforthe macrohas
beenpressed, continue to pressthe buttons you
wishto be padof the macro, i ntheordertheywill
beused.Press eachbuttonwithinfiveseconds of
the lastbutton, r emembering t o pressthe Input
SelectorE]P whenyouarechanging device
functions. Asthebuttons o n theremote are
pressed, the remote's display screen will show the
stepsin themacroastheyareprogrammed
(Figure 53).
[ _ U R ] P 0 I,! E r. 0 II
F_gure 53
9. Forourexample, wefirstwantthe AVRPower On
button pressed, f ollowed bytheTVPower On,
followed bythe CableBoxOn,followed bythe
selection of theLogic7 mode. # odo that,press
the buttons inthiso_der:
,, PowerOn
* VID2/TV
* PowerOn _1_
• VID3/Cable
• PowerOn
•AVR_
• Logic7
Aseachbuttonispressed to enterit intothe
macro, y ouwillseethe buttonnames appear a nd
thenscrollup onthe LCDdisplay asyourconfir
marion of the keyentry(Figure 53).
10.Whenall commands f or the macrohavebeen
entered, p ressthe Set Button _ to savethe
macro. T hedisplay screen will show the button
to whichthe macrohasbeenprogrammed a nd
the number o f stepsused, a ndthewordS_UED
will blinkfourtimesinthelowerlineof the LCD
display. Whenthe display returns to normal, t he
macrohasbeenentered andthe remote is ready
foroperation.
11. If a macrohasbeenprogrammed i ntothePower
On Button _, it will playbackanytime the
Power Onbuttonis pressed. Asthe macroplays,
youwillseethe stepsappear i nthe remote's LCD
display. Macros programmed i ntooneof thefour
discrete Macrobuttons maybe activated a t any
timeby pressing theappropriate b utton.
Erasinga Macro
Oncea macrohasbeencreated andstoredinthe
AVRremote's memory, you havetheopl_on of
erasing it.Youmaydo thisatanytimeby following
thesesteps:
1. Press andholdthe ProgramButton _ for
aboutthreeseconds whilethe message shown
inFigure 24 appears inthe remote's LOD
InformationDisplay_. Release t he button
whenthe redlightunderthe Set Button
appears.
2.Theremote's M6IH MEHUmessage (Fig.25),
willappear i nthe LCDdisplay andtheSet Button
will remain illuminated i n red.Pressthe•
NavigationButton _ threetimessothat
M_CROappears on the bottomlineofthe LCD
screen, a sshown in Figure 47. Press theSet
Button _ to enterthe mainmacromenu
branch.
3. At thenextmenuscreen(Figure 54), pressthe
• /T NavigationButton @ untilthe bottom
lineinthe remote's LCDdisplay readsEF.t_SE
MACRO.PresstheSet Button _ to beginthe
process of erasing a macro.
ERASE
_ M_CRO
F_gure 54