Optional Accessories - Nice Era Plus H Instructions And Warnings For Installation And Use

––– Procedure 5.13 performed using the Era P or Era W transmitter –––
01
...
04
PRG
3
1
sec.
6

OPTIONAL ACCESSORIES

6.1 - Control push-button (wall-mounted)
6.1.1 - Installation of the push-button strip
This accessory can be used as an alternative to the radio transmitter to send com-
mands to the motor by cable, when using the automated mechanism. The push-
button activates the "step-by-step" command: i.e. each time it is pressed, a differ-
ent command is sent in rotation from among the following: > up, > stop, > down,
> up, > ... .
Installation warnings:
• The mechanical operation of the push-button must only be of the "hold to run"
type: i.e. when released, the buttons must return to their initial position. N.B. –
When the limit switches are already adjusted, all you need to do is simply press the
push-button with one pulse to activate the movement of the awning/shutter which
will terminate automatically when it reaches the adjusted limit switch.
• The push-button strip must be positioned as follows: a) - in a position which is
not accessible to strangers; b) - within view of the awning/shutter but away from
its moving parts; c) - on the side of the awning/shutter where the electricity cable
from the motor and the electricity supply cable from the mains are found (fig. 4-h);
d) - at a height of not less than 1.5 m above the ground.
6.2 - Climate sensors for wind, sun, rain
ATTENTION! – Only radio-based sensors can be used. These accessories in-
dependently control the movements of the awning/shutter according to the atmos-
pheric conditions detected outdoors.
Warning – These climate sensors must not be considered as safety devices that
can eliminate failures in the awning/shutter caused by the effects of rain or strong
winds; a mere electricity blackout, in fact, would make the automatic movement of
" 1 "
05
PRG
4
1
sec.
07
=
sec.
07
=
sec.
07
new
=
"1"
sec.
02
PRG
2
1
sec.
06
5
sec.
3
5
3
5
3
5
the awning/shutter impossible. Consequently, these sensors must be considered as
components of the automated device, that are useful in protecting the awning/shut-
ter. Nice declines all liability for any material damages that occur due to atmospheric
events not detected by the sensors.
6.2.1 - Definitions and conventions
• Manual "Sun On" Command = enables the reception, by the motor, of auto-
matic commands transmitted by the "Sun" sensor if present in the installation.
When reception is enabled, the user can send manual commands at any time:
these override the automatic operation of the automated device.
• Manual "Sun Off" Command = enables the reception, by the motor, of auto-
matic commands transmitted by the "Sun" sensor, if present in the installation.
When the reception is disabled, the automated device operates exclusively with
the manual commands sent by the user. The "Wind" and "Rain" sensors cannot
be disabled because they protect the automated device from these atmospheric
phenomena.
• "Above-threshold" intensity of sun/wind = condition where the intensity of the
atmospheric phenomenon corresponds to high values above the set threshold.
• "Below-threshold" intensity of sun/wind = condition where the intensity of the
atmospheric phenomenon corresponds to low values below the set threshold.
• "Wind protection" = a condition in which the system inhibits all the awning/shut-
ter opening commands due to the intensity of the wind above the threshold.
• "Presence of rain" = a condition in which the system detects the presence of
rain, with respect to the previous condition of "absence of rain".
• "Manual command" = UP, DOWN or Stop command sent by the user by means
of a transmitter.
6.2.2 - Memorisation of a climate sensor connected via radio
To store a climate sensor to perform the procedure 5.11.
6.2.3 - Behaviour of the motor in each kind of weather condition
The NEMO and VOLO accessories allow the awning/shutter to be moved automati-
03
PRG
2
1
sec.
2
Inglese – 12