Optional Accessories - Nice Era Mat A Series Instructions And Warnings For Installation And Use

5.14 - Locking and unlocking the memory
This procedure allows you to lock or unlock the memory to prevent accidental memorization of other transmitters not included in the system.
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the s key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04. Keep the s and t keys pressed simultaneously and wait for the motor to perform 2 movements. Upon completion, release the keys.
05. • To lock the memory: keep the s key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
• To unlock the memory: keep the t key pressed and wait for the motor to perform 5 movements. Upon completion, release the key.
01
5
sec.
04
5
sec.
Note – When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
6

OPTIONAL ACCESSORIES

6.1 - Control pushbutton strip (wall-mounted)
6.1.1 - Installation of the pushbutton strip
This accessory can be used as an alternative to the radio transmitter to send, by wire, the controls to the motor when using the automation.
Installation warnings:
• It is recommended to use an unstable pushbutton strip with interlocked pushbuttons.
• The mechanical operation of the push buttons must be exclusively of the "with operator present" type: in other words, and they are released, they must return to their initial
position. Note - When the limit switches are already adjusted, all you need to do is simply press the pushbutton with one pulse to activate the movement of the rolling shut-
ter which will terminate automatically win it reaches the limits which you have adjusted.
• You can choose models with one or two pushbuttons according to your needs: the model with two push buttons activates the Raise and Lower input; the model with one
pushbutton can activate the TTBus / Open / Step-to-step (the type of input is selected with the procedure described in paragraph 6.1.2 - B).
• The pushbutton strip must be positioned as follows:
– in a place that is not accessible to outsiders/strangers;
– allowing you to see the rolling shutter but far from its moving parts;
– on the side of the rolling shutter where there is the electrical cord from the motor and the power cord from the electrical mains (fig. 4-h);
– at a height no less than 1.5 m from the floor/ground.
6.1.2 - Connecting the pushbutton strip
A - Pushbutton strip with 2 push buttons (wires to use: White + White-Orange + White-black): to connect this accessory, see fig. 3.
B - Pushbutton strip with 1 push buttons (wires to use: White + White-black): to connect this accessory, see fig. 3. After connection is completed, follow the proce-
dure below assign the desired command to the pushbutton: Open or Step-by-step (use a transmitter memorized in "Mode I").
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the s key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
05. • To assign the Open command to a pushbutton: keep the s key pressed and wait for the motor to perform 3 movements.
• To assign the Step-By-Step command to a pushbutton: keep the t key pressed and wait for the motor to perform 5 movements. Upon completion, release the key.
11 – English
02
2
2
3
5
sec.
05
5
sec.
05
5
sec.
03
3
5
sec.
THE
END
3
END
THE
END
5
END