Craftsman 10 IN. TABLE SAW 315.22811 Owner's Manual page 47

I
Key
No.
CRAFTSMAN 10 in. TABLE SAW - MODEL NO. 315.228110
PARTS LIST - FIGURE A
The model number will be found on a plate attached to the side panel of the cabinet. Always mention the model |
number in all correspondence regarding your TABLE SAW or when ordering repair parts.
I
Part Key Part
Number Description Quart. No. Number Description Quan
1 969214-008
2 663283-001
3 969600-001
4 969226-001
5 969101-005
6 662884-005
7 969103-005
8 969104-007
9 969105-005
10 969529-002
11 661694-003
12 969548-002
13 969176-905
14 969113-001
15 623924-002
16 662481-001
17 969193-001
18 **STD541031
19 969117-001
20 969924-001
21 969251-002
22 663144-001
23 969122-002
24 969123-002
25 969124-002
26 969125-002
27 969126-001
28 969127-001
29 969128-001
30 969129-002
31 998292-002
32 **STD541175
33 661796-001
34 969130-001
35 977227-002
36 981817-001
39 969222-001
40 969221-001
41 706382-359
42 706382-360
Motor Assembly ...................... 1
Off/On Switch Assembly ......... 1
Shim ........................................ 2
*Hex Nut (#5/8-18) .................... 1
Saw Table ............................... 1
Front Cabinet Panel ................ 1
Rear Cabinet Panel ................. 1
Right Cabinet Panel ................ 1
Left Cabinet Panel ................... 1
Locker Bracket ........................ 1
Clamper Bracket ..................... 1
Dust Cover .............................. 1
Miter Table Assembly .............. 1
Clamp Plate ............................. 2
Needle Roller
(1/4 in. x 3/4 in.) ...................... 2
Clamp ...................................... 1
Shim ........................................ 5
*Hex Nut (#5/16-18) .................. 2
Front Rail ................................. 1
Rear Rail ................................. 1
Rail Holder Nut (#5/16) ........... 4
Rail Locking Clamp ................. 4
Bevel Gear .............................. 2
Shaft ........................................ 1
Gear Shaft ............................... 1
Handle Shaft ........................... 1
Gear Rack ............................... 1
Tilting Gear .............................. 1
Clutch ...................................... 1
Cam ......................................... 1
*Screw
(#8-32 x 1-3/16 in. Fil. Hd,) ..... 1
*Hex Nut (#3/4-16) .................... 1
Washer .................................... 1
Locking Lever .......................... 1
Handwheel Assembly
(Includes Key No. 115) ............ 1
Handwheel Adapter ................. 1
Spring ...................................... 1
Spring ...................................... 1
Washer .................................... 1
Washer .................................... 3
43 706382-346
44 **STD523110
45 **STD523107
46 662493-002
47 **STD511007
48 **STD600803
49 **607406-005
50 **STD502503
51 941401-018
52 941401-831
53 981505-001
54 981506-001
55 969137-001
56 969138-001
57 989001-001
58 969140-001
59 **STD375005
60 **STD541408
61 969142-001
63 981504-001
64 **STD522510
65 **STD522520
66 **STD541025
67 968705-004
68 969230-001
69 969229-001
70 968702-011
71 664087-001
73 **STD501003
75 "*STDe01005
76 969605-004
78 969220-002
80 969212-001
Washer .................................... 4
*Hex Bolt
(#5/16-18 x 1 in.) ..................... 2
* Hex Bolt
(#5/16-18 x 3/4 in.) .................. 4
*Screw
(#10-24 x 5/8 in. Pan Hd.) ....... 8
*Screw
(#10-24 x 5/8 in. Pan Hd.) ....... 3
*Screw
(#8-32 x 3/8 in. Pan Hd.) ....... 16
*Nylon Hex Nut (#3/8-16) ......... 1
*Set Screw
(#1/4-20 x 3/8 in.) .................... 1
Roll Pin .................................... 1
Roll Pin .................................... 2
Name Plate ............................. 1
Scale Label ............................. 1
Outlet (15 Amp Single Pole).... 1
Cord ........................................ 1
Cable Clamp ........................... 1
Bevel Indicator ........................ 1
Wire Nut .................................. 1
"Lock Nut (#8-32 Hex) .............. 3
Cone Disc Spring .................... 1
Data Plate ............................... 1
*Bolt (#1/4-20 x 1 in. Hex) ........ 2
*Bolt (#1/4-20 x 2 in. Hex) ........ 1
*Hex Nut (#1/4-20) .................... 4
*Screw
(#10-24 x 5/16 in. Pan Hd.) ..... 2
Plug Socket Box (A) ................ 1
Plug Socket Box (B) ................ 1
*Screw
(#8-16 x 3/4 in. Pan Hd.) ......... 4
Locker Support ........................ 2
*Set Screw (#10-24 x 3/8 in.) ... 4
*Screw
(#10-24 x 1/2 in. Pan Hd.) ..... 15
Throat Plate ............................. 1
*Cap Screw
(#1/4-20 x 3/4 in.) .................... 1
Guide Holder ........................... 1
47 [RAFTSMAN" TABLE SAW315.228110