Lockly PGD628 Installation Manual
Hide thumbs
Also See for PGD628:
- Installation manual (24 pages) ,
- Installation manual (30 pages) ,
- Installation manual (23 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Lockly PGD628
Summary of Contents for Lockly PGD628
- Page 1 SECURE INSTALLATION GUIDE LATCH EDITION PGD628 | PGD628F | PGD628FC...
- Page 2 Welcome! This guide will walk you through step-by-step how to install and get your Lockly Secure up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: Lockly.com/support or call (669) 500-8835 for help.
- Page 3 Preparation To complete the installation you will need: Flathead Screwdriver Tape measure or ruler Phillips Screwdriver Pliers Screwdriver with drill bits （Optional） Drilling is not required to install the lock, and is optional. However if you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
- Page 4 Preparation Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. 1-3/8" ~ 2" (35mm ~ 50mm) Measure and confirm your door is between 1-3/8" ~ 2" ( 35mm - 50mm). 1/2"...
- Page 5 2-3/8" (60mm) this lockset, replace your door’s old lockset with the provided Lockly lockset. The included lockset is designed and optimized for Lockly smart locks. Measure the distance between center of front door hole to the edge of your door. Push the shaft (a) to adjust the lockset to 2-3/8"(60mm) or 2-3/4"(70mm).
- Page 6 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR INTERIOR LEFT IN-SWING DOOR Hinge Side LEFT OUT-SWING DOOR...
- Page 7 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Rotate the handle 180° to the other side of the Confirm that your installation was complete lock. by checking if the pins are flush against the handle, and has popped out. Adjust Using your fingers, press the two pins located on the handle accordingly to make sure the the left and right side of the the lock to insert...
- Page 8 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Changing the Interior Handle Orientation Securely screw clockwise as shown Remove the screw by turning counter to complete your handle orientation clockwise and rotate the handle 180° change. in the direction of the arrow as shown. Make sure the screw hole is aligned with the marker as illustrated.
- Page 9 Step 3 PREPARING LOCK FOR INSTALLATION If you drilled a hole in Preparation, use Slotted Barrel Extension and use pliers to securely tighten clockwise. If you did not drill a hole in Preparation, you can leave this pole removed. Peel paper layer OFF the Adhesive tape and prepare for installation.
- Page 10 Step 4 INSTALLING THE LOCK (EXTERIOR) Exterior Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset. Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.
- Page 11 Step 5 INSTALLING THE LOCK (INTERIOR) Interior Insert Positioning Rods into the holes to the left and right of the Spindle The holes are located at the 3 o’clock and 9 o’clock positions. Interior Mounting Plate will go against the interior side of your door. Remove the paper layer off of the Adhesive Tape align the positioning rods on the bottom of the plate to the corresponding left and...
- Page 12 Step 5 INSTALLING THE LOCK (INTERIOR) continued Secure with Pull the cable from the lock exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws Remove the position rods replace them with screws *Secure top with Tighten clockwise until the mounting plate is secure.
- Page 13 Step 5 INSTALLING THE LOCK (INTERIOR) continued Plug cable that is coming through the door into the lock interior Match red side of the plug with red on socket - insert tightly. Install Cable Remove Cable IMPORTANT: If you need to disconnect this cable, use a screwdriver to hold down the tab (marked red) before carefully unplugging.
- Page 14 Step 5 INSTALLING THE LOCK (INTERIOR) continued Once the lock interior is flush against the mounting plate, secure the lock to the plate by screwing clock- wise using provided screws Insert 4 AA batteries into the lock by aligning the positive and negative orientation markings...
- Page 15 Step 6 INSTALLING THE DOOR STRIKE Close your door to see if your lock closes securely with your existing door strike. If the lock closes securely, you may keep the existing door strike without removing the old hardware. However, it’s recommended that you use our door strike.
- Page 16 Step 7 DOWNLOAD THE LOCKLY APP Congratulations! You have completed the Lockly Secure physical lock installation. To complete your setup, download the Lockly app from the App Store or on Google Play and follow on-screen instructions. Scan or visit Lockly.com/app...
- Page 17 Add more Smart to your Home Secure Link Wi-Fi Hub Add the optional Lockly Secure Link Wi-Fi Hub, together with the free Lockly app, it's easier than ever to securely control and manage your door from anywhere, anytime. Real-time, monitoring, & status...
- Page 18 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 19 Clamping Tool Interior Adhesive Exterior Adhesive Slotted Barrel Extension Activation Card SAVE Positioning Rod LOCK SERIAL PGDxxxxxxxxxx Activation Card ACTIVATION CODE RFID Card (for PGD628FC only) xxxxxxxx SCAN & SAVE Mounting Plate Need help? Email: help@Lockly.com | Support: +1(669) 500-8835...
- Page 20 SECURE Go to Lockly.com/installation to download the latest version of this installation guide. Scan the code on your phone to watch step-by-step video installation.
-
Page 21: We're Here To Help
Bluetooth SIG, Inc. , and any ® use of such marks by Lockly is under license. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play and Google Home are trademarks of Google LLC. , Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc., or its affiliates.