Vitek VTD-TND5RMS Quick Start Manual

Components and Accessories
Quick start guide
Camera
CVBS&DC
Drill template
IN cables
Screwdriver
Sponge
Overview
1 RJ-45 Ethernet
2 Audio In
3 Audio Out
4 CVBS Output
5 Alarm I/O
Network Cable & Power Connections
First connect the Waterproof Cap to an Ethernet patch cable, then
connect the cameras ethernet adaptor. If not powering the camera with
PoE, also connect the power Cable to an approved 12VDC Power
Supply.
Optional 12VDC
Power Connection.
Not needed with PoE
Alarm Connection
A lar m I nput: Join the grounding ends of the sensor and the camera and then connect the
signal cable of the sensor to the alarm input port of the camera.
A lar m O utput: Loosen the screws in the alarm output port. Then insert the signal wires
of the alarm output devices into the port of COM and OPEN separately. Finally tighten
the screws. Some of the external alarm output devices need the power supply.
Weather Resistant Network Coupler
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
1
4 tapping screws PA 4×25
×4
Plastic plug
1
2
3
4
5
6
7
8 9
10
6 RS-485
7 Power Cable
8 Reset
9 Service Port
10 MicroSD Card Slot
2
ALM: COM
ALM: NO
ALM: IN
ALM: GND
RS-485 +
RS-485 -
QUICK START GUIDE
FEATURES
• 1/2.5" 5.0 Megapixel Progressive Scan CMOS image sensor
• Up to 30fps live view @ 5 MegaPixel (2592×1944)
• 3.3 ~ 12 mm Motorized Varifocal Lens
• 30 IR LED Illumination with a 100' IR Range
• 120dB Super Wide Dynamic Range (WDR)
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction
• Fully Programmable Intelligent Analytics including Face Detection,
Object Removal/Museum Search, Exception, Line Crossing, Area
Intrusion, People Counting, People Intrusion, Crowd Density Monitoring
• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps
• ONVIF Compliant
• Micro SD Card support up to 128GB
• IP66 Weather Resistance & IK10 Impact Rating
• Optional Mounts Available: Wall Mounts (VT-TWM03, VT-TWMT-A1),
J Box (VT-TJB02A), Pedestal Mount (VT-TPDMT-A1)
• 12VDC & PoE (Power over Ethernet) Operation
• Charcoal finish available, use model # VTD-TND5RMSB
FOR FULL PRODUCT MANUAL
SCAN THE QR CODE BELOW
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
the screw holes and 1 cable
hole according to the drill
template.
2. Loosen the screws to open
the lower dome and then
loosen the lock screw to
remove the mounting base.
3. Route the cables and
connect the power & video
cables, use the rubber plug
to fill the gap of the mounting
base. Then secure the
mounting base to the ceiling
or wall with screws.
VTD-TND5RMS
Transcendent Series
5 Megapixel H.265 Indoor/
Outdoor WDR IP Dome Camera
with 30 IR LED Illumination
4 3
88 mm
∅6
∅148
∅22
89mm
Lock Screw
Lower Dome
Sponge
Mounting Base