Charlton & Jenrick Luminosa 150 Installation & Operation Manual

Charlton & Jenrick Luminosa 150 Installation & Operation Manual

Real flame technology
Hide thumbs Also See for Luminosa 150:

Advertisement

Best of British fires, fireplaces & stoves
Installation & Operation Manual
Real Flame Technology
Model: Luminosa 150
Please read the instructions carefully before installation
or use and keep for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Luminosa 150 and is the answer not in the manual?

Questions and answers

Summary of Contents for Charlton & Jenrick Luminosa 150

  • Page 1 Best of British fires, fireplaces & stoves Installation & Operation Manual Real Flame Technology Model: Luminosa 150 Please read the instructions carefully before installation or use and keep for future reference.
  • Page 3: Table Of Contents

    CONTENTS ………………………………………………… Important Safety Information ……………………………………………………… Technical Specifications …………………………………………………………… Parts And Hardware ………………………………………………………… Appliance Dimensions ……………………………………………………… Installation Instructions ………………………………………………………… Operating Instructions …………………………………………………… Manual Control Panel ………………………………………………………… Remote Control ……………………………………………………………… APP Control …………………………………………………………………… Maintenance ………………………………………………………………… Service Parts list …………………………………………………………………………… Others...
  • Page 4: Important Safety Information

    1. IMPORTANT SAFETY INFORMATION Read all of the instructions carefully before using the Ÿ appliance. For indoor use only. This appliance is not suitable for use Ÿ outside the house. Do not use this appliance in the immediate surroundings of Ÿ...
  • Page 5 This appliance is not intended for use by persons Ÿ (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Page 6: Technical Specifications

    2. TECHNICAL SPECIFICATIONS Model No. : Luminosa 150 Supply Voltage: AC 230-240 V 50 Hz Maximum power consumption: 1800-2000 W Power for flame and fuel bed effect: 65 W Power for mood light: 9 W Heat Output: Nominal heat output (Pnom): 2000 W...
  • Page 7: Parts And Hardware

    3. PARTS AND HARDWARE 3.1 Unpack the fire carefully and make sure that the appliance is intact with no signs of damage caused by transport and no part has been exposed to water. If in doubt, do not use the appliance and contact your retailer.
  • Page 8 Power Cord Bracket (1pc) (Installer must fit before Power Cord (1pc) Sucker(2pcs) leaving appliance) Crystal Media Large (1set) Crystal Media Medium (1set) Crystal Media Small (1set) Black Resin Chips (1set) Logs (1set) Vermi culate (1set) Be st of Br iti sh fir es , fir ep la ce s &...
  • Page 9: Appliance Dimensions

    4. APPLIANCE DIMENSIONS Unit:mm 1500 1532...
  • Page 10: Installation Instructions

    5. INSTALLATION INSTRUCTIONS 5.1 PREPARATION BEFORE INSTALLATION TOOLS REQUIRED A screwdriver, a spirit level and drill will be needed. LOCATE THE APPLIANCE Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location, ensure that the general instructions are followed: For best result, install out of direct sunlight, water or very damp air.
  • Page 11 CONNECT MOOD LIGHTS CABLE The interface of the mood lights cable is on the top of the appliance, Ÿ near the position of the power cord. Please also check the function after connecting the mood light. Note: Compa ble mood ligh ng devices are available from Charlton & Jenrick Ltd., Other brands may not be suitable and void the warranty.
  • Page 12 REMOVE WALL MOUNTING BRACKET Remove the wall mounting bracket from the rear of the appliance by Ÿ removing the securing screws. CHOOSE ASPECT TYPE The appliance can be installed in 3 different arrangements. They are as follows: Front view (only the front window is visible) Ÿ...
  • Page 13 Panoramic Aspect (the front and both sides windows are Ÿ visible) Repeat the corner aspect procedure on the opposite side of the appliance. 5.2 CHOICE OF INSTALLATION METHOD The following is only given as a general guide because it can be installed in so many ways.
  • Page 14 CORNER VIEW PANORAMIC VIEW Recommended Cavity Dimensions (mm) Front Corner Panoramic 1540 1525 1510 Min 270 These dimensions are a guide. Always measure the appliance on site before cutting the cavity. NOTE: Ensure a firm flat surface for positioning of the appliance and securely fix to avoid vibration and movement of the appliance.
  • Page 15 Bend out the four brackets on the upper and lower edges of the Ÿ appliance, push the appliance into the framework and fix the appliance with four ST4x40 screws provided to the framework. is important that the appliance is fitted securely as described below.
  • Page 16 There are two fuel bed arrangements for you to choose: A. Decorative Log Set Arrangement Fix the log led to the fuel bed, and then place the four logs with slot Ÿ on it. Freely arrange other logs and when you are happy with the layout, Ÿ...
  • Page 17 B. Crystal Media Arrangement Scatter the small crystal media around the fuel bed, ensuring that Ÿ all visible areas are covered. Freely place the large and medium crystal media on the fuel bed. WALL MOUNTED Place the wall mounted bracket horizontally against the wall where Ÿ...
  • Page 18 Lift the appliance up and attach to the wall mounting bracket by Ÿ locating the fingers on the wall bracket into the rectangular openings in the rear of the appliance. Mark the hole position of the bottom mounting brackets, remove the Ÿ...
  • Page 19: Operating Instructions

    6. OPERATING INSTRUCTIONS WARNING! Do not operate the appliance if it is damaged or malfunctions. If you suspect the appliance is damaged or malfunctions, call a qualified service engineer to inspect the appliance, and replace any part of the electrical system if necessary, before reusing. WARNING! To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 meter from the air...
  • Page 20: Manual Control Panel

    THE BOOT PROCESS FOR FLAME EFFECT Switch on the appliance by MAIN SWITCH, then press “STAND-BY” button on the appliance. The fuel bed starts to blink and the screen displays “WELCOME”. The booting process will take about 30 seconds and flame effect will be turned on. If you turn off the flame effect using the STANDBY button, the flame effect will remain dormant for 20 minutes ,after that you can turn on the flame immediately.
  • Page 21: Remote Control

    6B. REMOTE CONTROL NOTE: The start-up time of the screen is 30 seconds, During this period, “WELCOME” is displayed on the screen, the fuel bed starts to flash, and the appliance cannot be operated. After that, the fuel bed stops flashing, the flame will be turned on, and the appliance can be operated normally.
  • Page 22 NOTE: The remote control handset must be left in the same room as the appliance because it houses the thermostat that regulates heat output. Also, when using the APP, the remote must also be in same room and have batteries fitted and working to ensure accurate temperature control.
  • Page 23 Press the ' ' and ' ' button to select the 5 levels of brightness. Down Light/Ambient Light Note: If mood lights are not connected, please ensure the brightness is set to zero. Press once until shows on the screen to enter the down light setting mode. Press the ' ' and ' ' button to select 2 different down light colours and OFF...
  • Page 24 Window Open Detection When the transmitter detects a rapid drop in room temperature, it will be judged as a window open, the warning icon will be displayed and the heater will be turned off automatically. After the indoor temperature has risen or a manual override of the warning (by operating remote control) has been done, the fire will return to normal working state.
  • Page 25: App Control

    6C. APP Control Visit your APP store for IOS or Android to download the C&JsmartFIRE APP. Or use the QR code below. Follow your devices onscreen instructions to create an account. Once installed, follow the procedure below to pair the device with your appliance.
  • Page 26: Maintenance

    7. MAINTENANCE WARNING: Before any maintenance or cleaning of the exterior of the appliance, the unit should be disconnected from the power supply remove supply plug from power socket or turn off and remove fuse from fused spur, wait until the appliance is cool.
  • Page 27: Service Parts List

    8. SERVICE PARTS LIST...
  • Page 28 Item Part Number LED Model 1 Side Glass 8626 2 Metal Side Panel 8619 3 Top Edging Strip 1 8641 4 Back Edging Strip 2 8640 5 Bo om Edging Strip 3 8639 6 Control Panel 9709 7 Spindle Motor 9710 8 Speaker 8888...
  • Page 29: Others

    9. OTHERS Environment Meaning of crossed –out wheeled dustbin: Electrical appliances should not be disposed as unsorted municipal waste. Separate collection facilities should be used in the disposal of electrical appliances. Contact your local government for the information about the available collection systems.
  • Page 32 Help And Advice Contact: Kemian Industries 3 French Ave,Bendale, QLD 4500 Tel: 07 3490 5500...

Table of Contents