Menu Settings; Access The Settings Menu; Exit The Menu; Rinse - DeLonghi DINAMICA plus Instructions For Use Manual

Danger of scalding!
During rinsing, a little hot water comes out of the coffee spouts
(A9) and is collected in the drip tray (A15) underneath. Take care
to avoid contact with splashes of water.
1. To turn the appliance off, press the
(fig. 7).
2. The appliance performs a rinse cycle then goes off
(stand-by).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket.
Important!
Never unplug while the appliance is on.

6. MENU SETTINGS

6.1 Access the settings menu

1. Press the " " button (C3) to enter the menu;
2. Scroll through the menu items by pressing
until the required item is displayed;
3. Press the menu item you want to select.

6.2 Exit the menu

When you have made the adjustments, press
you are back on the homepage.
6.3

Rinse

Use this function to deliver hot water from the coffee spouts
(A9) to clean and heat the appliance's internal circuit.
1. Place a container with a minimum capacity of 100ml under
the coffee spouts (fig. 8).
2. A few seconds after the "RINSE" item has been selected,
hot water is delivered from the coffee spouts to heat the
appliance's internal circuit (fig. 8).
3. To stop rinsing, press
stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the grounds container (A11)
to contain water.

6.4 Descaling

For instructions on descaling, see section "13. Descaling".

6.5 Water filter

For instructions on how to install the filter (D6), see section "15.
Water softener filter".
button (A15)
until
or wait for rinsing to
7

6.6 Beverages settings

In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage.
1. Once in the settings menu, press "DRINK SETTINGS". The
values for the first beverage appear on the display;
2. The values are displayed on vertical bars. The default value
is indicated by the
highlighted by the solid part of the vertical bar;
3. To go back to the settings menu, press
scroll and display the beverages, press
4. To reset the default values for the beverage displayed,
press ;
5. "CONFIRM RESET?": to confirm, press
cel, press
6. "DEFAULT VALUES SET": press
The beverage has been reset to the default values. Proceed with
the other beverages or go back to the homepage by pressing
twice.

6.7 Auto-off (standby)

Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press "AUTO-OFF";
2. Select the required time interval by pressing the selection
arrows (increase) or
3. To confirm, press
Auto-off is now programmed.
6.8

Energy saving

Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
Press "ENERGY SAVING" to disable (
function;
The corresponding symbol (B1) appears on the top bar of the
homepage to indicate that the function has been enabled.
Please note:
If energy saving is active, you may have to wait a few seconds
before delivery.

6.9 Coffee temperature

To change the temperature of the water used to make the cof-
fee, proceed as follows:
"COFFEE TEMPERATURE"
1. Press
pear on the display (the current value is underlined);
2. Press the value you want to set (LOW, MEDIUM, HIGH).
symbol, while the current value is
);
.
(decrease);
.
) or enable (
. The selectable values ap-
. To
;
(to can-
) the