Table of Contents
Advertisement
•
Clean the water level limiting device regu-
larly and check for signs of damage.
Before emptying the container, unplug the machine.
Disconnect the hose from the inlet by pulling out the
hose. Release the latch by pulling them outwards
so that the motor top is released. Lift up the motor
top from container. Always empty and clean the con-
tainer and water level limit system after picking-up
liquids.
Empty by tilting the container backwards or side-
ways and pour the liquids into a floor drain or similar.
Put back the motor top to the container. Secure the
motor top with the latches.
Heavy maneuvers can, by mistake, trigger the water
level limiting device. Should this happen; turn off the
machine and wait for 3 seconds to reset the device.
Continue to operate the machine afterwards.
3.9
Dry pick-up
CAUTION
Picking up environmentally hazardous materi-
als.
Materials picked up can present a hazard to
the environment.
•
Dispose of the dirt in accordance with le-
gal regulations.
CAUTION
Dust Class H machines are equipped with an
upstream Dust Class H filter fitted on bottom
side of motor top under a guard cover.
Check that filter guard cover and sealing are
safety installed and without damage and that
the filter is properly fitted.
A LED indicator will light if the filter needs to
be replaced, or if the filter is missing, mounted
incorrectly or damaged.
Remove the electrical plug from the socket before
emptying after dry pick-up. Remove the suction hose
from the machine and close the inlet cap, to avoid
harmful dust spreading. Release the latch by pulling
them outwards so that the motor top is released. Lift
up the motor top from container.
Main Filter: check the filter. To clean the filter you
can either brush or wash it. Wait until the filter is dry
before re-starting dust pick-up.
Essential Filter Dust Class H: check the filter. Re-
place filter if necessary. Wear mask and protective
clothing.
Dustbag: check bag to ensure the fill factor. Re-
place dust bag if necessary. Remove the old bag.
The new bag is fitted by passing the carboard piece
with the rubber membrane through the vacuum inlet.
Make sure that the rubber membrane is passing past
the heightening at the vacuum inlet.
Safety filter bag: check bag to ensure the fill factor.
Replace dust bag if necessary. Wear mask and pro-
tective clothing when removing the old bag. Carefully
8
OEL=Occupational Exposure Limit,
1)
*)
remove the dust bag connection from the inlet fitting.
Close the dust bag connection with the slide. Dis-
pose of the dirt in accordance with legal regulations.
After emptying: close motor top to the container
and secure the motor top with the latches. Never
pick up dry material without filter fitted in the ma-
chine. The suction efficiency of the machine de-
pends on the size and quality of the filter and dust
bag. Therefore - use only Original filter and dust
bags.
4
After using the machine
4.1
After use
After picking up hazardous dust, close the inlet cap
and clean the outside of the machine.
Remove the plug from the socket when machine is
not in use. Wind up the cord starting from the ma-
chine. The power cord can be wound up around the
motor top or at the container or placed in the includ-
ed hook, or fastening means. Some variants have
special storage places for accessories.
4.2
Transport
•
Before transporting the machine, close all the
latches.
•
Close the inlet with the inlet cap.
•
Do not tilt the machine if there are liquids in the
dirt tank.
•
Do not use a crane hook to lift the machine.
•
Do not lift the machine by the trolley handle *)
4.3
Storage
CAUTION
Store the appliance in a dry place, protected
from rain and frost. The machine shall be
stored indoors only. Wet filters and the interior
part of the liquid container shall be dried be-
fore storage.
4.4
Accessory and tool storage
For convenient transport and storage of accesso-
ries or tools, integrated rails are found on side of
machine which allows fastening with straps or other
means. A flexible strap and hooks are included on
back of machine for attachment of suction hose or
mains cable. For instruction see quick reference
guide.
An optional adapter plate
can be installed on top of machine for fastening of
2-point or 4-point storage cases.
Remove the electrical plug from the socket before
installing the adapter plate.
CAUTION
Do not lift machine in adapter plate without
having storage case safely installed. Note the
weight and balance of the appliance in case of
storage. Maximum weight of storage cases is
30 kg.
Optional accessories / Option depending on model
*)
with attachment system
*)
*)
Original instruction
Advertisement
Table of Contents
