Table of Contents
Advertisement
Air hose (ID)
Weight
A-Weighted sound
pressure level
Sound power level
Vibration value
Uncertainty
Noise emission values are in accordance with EN ISO
15744.
Vibration emission value is in accordance with EN 12096
and ISO 28927-1.
AppLIcAtIONs
The product is ideal for smoothing concrete, removing
burrs from metal and for finishing weld seams. It features a
rugged die-cast aluminum body and an ergonomic rubber
grip. It has built-in regulator for positive speed control,
screened inlet to prevent dirt particles from entering air
intake. Any other use is forbidden.
REsIDuAL RIsks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of injury
and damage remain. The following dangers can arise in
connection with the structure and design of this product:
1. Health defects resulting from vibration and noise
emission if the product is being used over long periods
of time or not adequately managed and properly
maintained.
2. Injuries and damage to property due to broken cutting
attachments or the sudden impact of hidden objects
during use.
3. Danger of injury and property damage caused by
flying objects.
AIR suppLy AND OpERAtION
■ Ensure air valve (or trigger) is in the "off" position
before connecting to the air supply.
■ Connect the product to the air hose.
■ Press the trigger to operate the product.
■ Do not apply additional force on the product.
■ Do not allow the product to free run for an extended
period of time as this will shorten its life.
■ Release the start and stop device in the case of an
interruption of the energy supply.
■ Disconnect the product from the air supply before
changing accessories or making adjustments.
■ Required air pressure of 6.3 bar (90 psi), and an air
flow according to specifications.
■ To mount the grinding wheel, insert a clamp nut then
9.52 mm (3/8")
1.3 kg (2.86 lb.)
79 dB(A), k=3 dB
90 dB(A), k=3 dB
2.4 m/s 2
0.79 m/s 2
the grinding wheel on the spindle before fitting the
other one.
■ Use the straight wrench and the pin wrench to tighten
the clamp nut for securing the disc.
■ Apply straight wrench on the inside "D" shape of the
spindle shaft.
■ Apply the pin wrench to tighten or loosen.
■ Before operation, ensure the inserted accessory is
fixed in the product.
Ensure the air supply is clean and does not exceed
6.3 bar (90 psi) while operating the product. Too high an
air pressure and unclean air will shorten the product's
life due to excessive wear, and may be dangerous
causing damage and/or personal injury.
LuBRIcAtION
An
automatic
in-line
recommended (Fig. 7) as it increases product life and
keeps the product in sustained operation. The in-line
lubricator should be regularly checked and filled with air
tool oil.
Proper adjustment of the in-line lubricator is performed by
placing a sheet of paper next to the exhaust ports and
holding the throttle open for approximately 30 seconds.
The lubricator is properly set when a light stain of oil
collects on the paper. Excessive amounts of oil should be
avoided.
If it becomes necessary to store the product for an extended
period of time (overnight, weekend, etc.), it should receive
a generous amount of lubrication at that time. The product
should be run for approximately 30 seconds to ensure oil
has been evenly distributed throughout the product. The
product should be stored in a clean and dry environment.
● It is most important that the product be properly
lubricated by keeping the air line lubricator filled
and correctly adjusted. Without proper lubrication
the product will not work properly and parts will
wear prematurely.
● Use correct lubricant in the air line lubricator. The
lubricator should be of low air flow or changing air
flow type, and should be kept filled to the correct
level. Use only recommended lubricants, specially
made for pneumatic applications. Substitutes
may harm the rubber compounds in the product's
O-rings and other rubber parts.
4
WARNING
filter-regulator-lubricator
is
Advertisement
Table of Contents
