Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi RA-AG100-B
Summary of Contents for Ryobi RA-AG100-B
- Page 1 RA-AG100-B AIR ANGLE GRINDER OpERAtOR’s MANuAL ORIGINAL INstRuctIONs...
- Page 2 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications.
- Page 3 DEscRIptION 1. Auxiliary handle 4. Guard 7. Straight wrench 2. Grinding wheel 5. Trigger 8. Pin wrench 3. Clamp nut 6. Nitto style coupler Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 Fig.6 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler...
-
Page 4: General Safety Rules
GENERAL sAfEty RuLEs ENtANGLEMENt hAzARDs Choking, scalping and/or lacerations can occur if loose ■ For multiple hazards, read and understand the safety clothing, personal jewelry, neck wear, hair or gloves are instructions before installing, operating, repairing, not kept away from the tool and accessories. maintaining, changing accessories on, or working near, the grinder. -
Page 5: Workplace Hazards
■ When using a grinder, the operator should adopt a or hydraulic hose. comfortable posture while maintaining secure footing ■ Proceed with care in unfamiliar surroundings. There and avoiding awkward or off-balanced postures. The can be hidden hazards, such as electricity or other operator should change posture during extended utility lines. -
Page 6: Vibration Hazards
increase in noise. ■ Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings. ■ If the grinder has a silencer, always ensure that it is in place and in good working order whenever the grinder ■... -
Page 7: Residual Risks
the grinding wheel on the spindle before fitting the Air hose (ID) 9.52 mm (3/8") other one. Weight 1.3 kg (2.86 lb.) ■ Use the straight wrench and the pin wrench to tighten the clamp nut for securing the disc. A-Weighted sound 79 dB(A), k=3 dB ■... -
Page 8: Troubleshooting
■ Maintenance shall be performed weekly. IMpORtANt! ■ Drain the air tank daily. Water in the air line will See Figure 7. damage the product. If a filter/regulator/lubricator is not installed on the air ■ If the product cannot be used anymore, make sure to system, air operated tools should be lubricated at least dispose of it so as not to impose hazards on people once a day or after 2 hours of work with 2 - 6 drops... -
Page 9: Possible Cause
chamber. Severe operating conditions may require more frequent lubrication. pROBLEM: Tool runs slowly. Air flows slightly from exhaust. pOssIBLE cAusEs ■ Motor parts are jammed with dirt particles. ■ Air regulator is in closed position. ■ Air flow is blocked by dirt. REMEDIEs ■... - Page 10 pARts LIst Description Description Description Description Grinder body Steel ball Dw=3 Bolt M5*6 Clamp nut Trigger Rotor Auxiliary handle Grinding wheel Pin 3 x 24 Rotor blades Washer Straight wrench Air inlet Cylinder Retainer washer 10 Pin wrench Rotor washer Transmission gears Oil pot Pin knob...
- Page 11 techtronic Industries (Australia) pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia techtronic Industries New zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand...