Schulze E-Power Duo Press Instruction Manual

Electric heat press
Hide thumbs Also See for E-Power Duo Press:

Advertisement

Quick Links

Instruction manual
electric heat press
SCHULZE E-Power Duo Press
1/14
Version 21.02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E-Power Duo Press and is the answer not in the manual?

Questions and answers

Summary of Contents for Schulze E-Power Duo Press

  • Page 1 Instruction manual electric heat press SCHULZE E-Power Duo Press 1/14 Version 21.02...
  • Page 2: Table Of Contents

    Introduction Content 1. Introduction 1.1 Content 1.2 Warning pictograms on the machine 1.3 Construction of the machine 1.4 Technical data 1.5 Replaceable heating plates 1.6 Replaceable base plates 1.7 Protection of the device 1.8 Safety arrangements at the workplace 1.9 Environmental protection 2.
  • Page 3: Warning Pictograms On The Machine

    Warning pictograms on the machine 3/14 Version 21.02...
  • Page 4: Construction Of The Machine

    12. Main switch Switch START 13. Emergency button Spiral tube with connection to the heating plate 1.4 Technical data Technical data SCHULZE E-Power Duo Press Dimensions of the press 95 x 80 x 155 cm Weight 180 kg Power supply...
  • Page 5: Replaceable Base Plates

    If any irregularities regarding functionality or safety are found during the testing, these has to be noted and reported to Walter Schulze GmbH in written form within 7 days. Until the clarification the machine can not be used. Information and education According to §81 the industrial law and §...
  • Page 6: Environmental Protection

    2.1 Notes regarding transportation The SCHULZE E-Power Duo Press is covered in protective foil and fixed onto the pallet for transport. Right after receiving it must be checked if the cardboard and the machine are in good condition without damages. It has to be done just after receiving the goods from the transportation company and in accompany of a responsible person.
  • Page 7: Working With The Heat Press

    3.2 Error codes The electronic devices of the SCHULZE E-Power Duo Press controls the main functions of the press. List of possible messages: ERR.1 – No connection of the electronic devices to the temperature sensor, (Temperature sensor defect/ cable not connected) ERR.2 –...
  • Page 8: Druckeinstellung

    3.4 Pressure adjustment With SCHULZE E-Power Duo Press it’s possible to adjust the pressure settings very precisely. Pressure can be adjusted with a knob, which is situated in the front of the press. Follow the instructions below to adjust the pressure: 1.
  • Page 9: Monthly Maintenance

    4.2 Monthly maintenance Before beginning maintenance work switch off the press, unplug it and wait until it gets cold. Some movable parts need to be greased. Greasing should be performed 2-3 times a year. You may use normal, heat resistant (up to 160°C) grease grease...
  • Page 10: Instruction For The Replacement Of The Electronics Keyboard

    4.6 Instruction for the replacement of the electronics keyboard To change the electronics keyboard the press must be switched off and unplugged. Remove the cover like in chapter 4.4. Disconnect the plug of the electronics keyboard from the electronics. Remove the keyboard from the press. Install a new keyboard and connect the plug to the electronics.
  • Page 11 Buttons on the keyboard are not working. It is Electronic’s keyboard is damaged Replace the electronic’s keyboard impossible to set the temperature or the time. Time does not count down after closing the START switch is damaged If after pushing and holding the switch START heat press.
  • Page 12: Documentation

    5 . Documentation 5.1 Connection diagram 12/14 Version 21.02...
  • Page 13: Configuration Of The Frequency Inverter

    5.3 Warranty terms and conditions Schulze heat presses and machines used for screen printing have a warranty for 24 months. This warranty includes the whole construction of the machine, mechanical elements, electronic device and covers. Expandable parts, fuses and safety covers are not included in the warranty terms.
  • Page 14: Conformance Declaration

    CONFORMANCE DECLARATION nr EPOWER/05/21/01 Manufacturer ROMANIK Andrzej Romanik ul. Przemysłowa 10 84 - 240 Reda, Poland hereby declares that the following machine: Heat press SCHULZE E-Power Duo Press is compliant with the specifications of the followings EC directives: Machinery (2006/42/EC)

Table of Contents