1. Manuals
  2. Brands
  3. Schulze Manuals
  4. Power Tool
  5. BluePRESSLine Size 3-S
  6. Instruction manual

Schulze BluePRESSLine Size 3-S Instruction Manual

Heat press
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
Version 10.01
Heat press
BluePRESSLine
Size 3-S
Version 10.01
1/16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BluePRESSLine Size 3-S and is the answer not in the manual?

Questions and answers

Related Manuals for Schulze BluePRESSLine Size 3-S

Summary of Contents for Schulze BluePRESSLine Size 3-S

  • Page 1 Instruction Manual Version 10.01 Heat press BluePRESSLine Size 3-S Version 10.01 1/16...

  • Page 2: Table Of Contents

    1. Introduction 1.1 Content 1. Introduction 1.1 Content 1.2 Illustration of the heat press 1.3 Technical Data 1.4 Safety arrangements of the heat press 1.5 Safety arrangements at the workspace 2. Initiation 2.1 Tips for transport 2.2 Installation of the heat press 2.3 Power supply 2.4 Initiation of the heat press 3.

  • Page 3: Illustration Of The Heat Press

    1.2 Illustration of the heat press Adjustment of the tension springs Electronic devices Base plate with silicon mat Enlargement plate Heating plate 10. Main fuse Contact pressure adjustment 11. Main switch Electromagnet 12. coiled cabel Compression lever with rubber grip 13.

  • Page 4: Safety Arrangements Of The Heat Press

    The testing should be protocoled. If any irregularities regarding functionality or safety are found during the testing, these have to been noted and reported to Walter Schulze GmbH in written form within 7 days. Until clarification the press can not be used.

  • Page 5: Initiation

    2.3 Power supply The BluePRESSLine Size 3-S has to be connected to a voltage of 230VAC/ 50Hz. The press is equipped with a plug. Make sure that the power outlet is in the right condition and that the grounding is connected to the power outlet.

  • Page 6: Working With The Heat Press

    3. Working with the heat press Programming the electronic devices After switching on the press, the current temperature is shown on the display and the press heats up. Change settings: The programming mode shows up when you press Button 1 for about 5 seconds, until the LED1 blinks up.

  • Page 7: Bugfixing Of The Electronic Devices

    3.2 Bugfixing of the electronic devices The electronic devices of the BluePRESSLine Size 3-S heat press control the main functions of the press. Here is a list of possible messages: ERR.1 – No connection of the electronic devices to the temperature sensor, (Temperature sensor defect/ cable not connected) ERR.2 –...

  • Page 8: Pressure Settings

    Pressure adjustments You can adjust the pressure very exactly. To do this, follow this explanation: Put a textile on the workplate. Close the heat press and control the pressure, after that, open the heat press. Turn the knop right to increase the pressure. •...

  • Page 9: Maintenance

    4. Maintenance 4.1 Daily Maintenance The working surface of the heating plate and the base plate have to be clean. The heating plate can be cleaned with a clean, dry cloth. Avoid contact with the heating plate – risk of burns. The silicon gum can be cleaned with a soft cloth. You can use mild household detergent.

  • Page 10: Replacing The Main Fuse

    4.3 Replacing the main fuse If the heat press does not work after switching on, check the main fuse of the press. The main fuse 12 A is placed at the upper part of the heat press next to the main switch (photo 1). To exchange the fuse, switch off the heat press first and pull the plug.

  • Page 11: Replacing The Electronic Devices

    4.5 Replacing the electronic devices Inside the heat press are the electronic devices, which are controlling the time and the temperature. For an exchange of the electric devices turn off the press and pull the plug. Release the fixation screws (photo 1) and remove the back cover (photo 2). Disconnect the green plug (photo 3), and take out the electronic devices (photo 4).

  • Page 12: Replacing The Silicon Mat

    4.7 Replacing the silicon mat To replace the silicon mat the press has to be cold and disconnected from the electricity. For the exchange you need a new silicon mat, silicon glue, acetone and a notched trowel. Remove the silicon mat completely with a knife . Clean the plate and the new silicon mat with acetone.

  • Page 13: Replacing The Temperature Sensor

    4.9 Replacing the temperature sensor The replacement must be done by an authorized person. To replace the temperature sensor switch off the heat press, pull the plug and wait until the heat press is cool. 1. Screw the cap and take out the insulation loose (Photo 1) 2.

  • Page 14: Troubleshooting

    – temperature too low or high after message, call Walter Schulze GmbH Heat press raises very slowly – 30 minutes One half of the heating plate do no raise adjusted temperature...

  • Page 15: Connection Diagram

    4.11 Connection diagram Version 10.01 15/16...

  • Page 16: Testing Report

    EN 292-1 EN 292-2 safety of machines EN 60204-1 electrical equipment of machines Berlin , .._____________________________ Peter Meidinger President All SCHULZE heat presses are exempt from the waste disposal law under reg. no. DE 231060054. Version 10.01 16/16...

Table of Contents