Schulze BluePRESSLine Mug 4 plus Instruction Manual

Schulze BluePRESSLine Mug 4 plus Instruction Manual

Heat press

Advertisement

Quick Links

Instruction manual
Version 15.01
Heat press
BluePRESSLine
Mug 4 plus
Version 15.01
1/14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BluePRESSLine Mug 4 plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Schulze BluePRESSLine Mug 4 plus

  • Page 1 Instruction manual Version 15.01 Heat press BluePRESSLine Mug 4 plus Version 15.01 1/14...
  • Page 2: Table Of Contents

    1. Introduction 1.1 Content 1. Introduction 1.1 Content 1.2 Heat press illustration 1.3 Technical data 1.4 Replacing of the heating element 1.5 Safety arrangements of the heat plate 1.6 Safety arrangements at the workspace 2. Initiation 2.1 Tips for transport 2.2 Installation of the heat press 2.3 Power supply 2.4 Initiation of the heat press...
  • Page 3: Heat Press Illustration

    1.2 Heat press Illustration Electronic devices Kontrol plate Pressure adjustment screw Pressure lever Main switch Movable part 10. Main fuse Heating band 11. Power cable with connector Fixation of the heating element 1.3 Technical Data Press dimension: ..........73 x 35 x 27 cm Weight: ................27 kg Operating voltage: ............230 VAC Rated power: ..............1300 W...
  • Page 4: Replacing Of The Heating Element

    If any irregularities regarding functionality or safety are found during the testing, these have to been noted and reported to Walter Schulze GmbH in written form within 7 days. Until clarification the press can not be used.
  • Page 5: Initiation

    2.3 Power supply The BluePRESSLine MUG 4 plus has to be connected to a voltage of 230VAC/ 50Hz. The press is equipped with a plug. Make sure that the power outlet is in the right condition and that the grounding is connected to the power outlet.
  • Page 6: Working With The Heat Press

    3. Working with the heat press 3.1 Programming electronic devices After switching on the press, the welcome is shown on the display. Press button „-” to choose the heating element which you want to switch on oder switch off. To confirm press button SETUP. There is two mode settings.
  • Page 7 15. Press button „ECO” about 3 seconds – go to the ECO settings. „Eco 0” - ECO mode is deactivated „Eco 1” - ECO mode is activated; after 30 min temperature will decrease by 50°C, after next 60 min the heating element will be switched off. „Eco 2”...
  • Page 8: Bugfixing Of The Electronic Devices

    3.2 Bugfixing of the electronic devices The electronic devices of the BluePRESSLine MUG 4 plus heat press control the main functions of the press. Here is a list of possible messages: ERR.1 – No connection of the electronic devices to the temperature sensor, (Temperature sensor defect/ cable not connected) ERR.2 –...
  • Page 9: Application Range And Sample Adjustments Of The Heat Press

    3.4 Application range and sample adjustments of the heat press This heat press is made for transfers to cups and pitchers. Here are some settings. Settings sublimation to a cup (Example): – Print temperature 180°C – Time 4 minutes You must never close the heat press without a cup inside! 3.5 Apply a transfer film to a cup Insert the cup with the transfer film Press the cup into the heating...
  • Page 10: Replacing Of The Heating Band

    3.7 Replacing of the heating band Before you change the heating band, switch off the heat press and pull the plug out from the wall outlet. The heating band must be cooled. 1. Unscrew the heating band and take it out (photo 1 and 2). 2.
  • Page 11: Replacing Of The Electronic Devices

    4.3 Replacing of the electronic devices The electronic devices are placed inside the heat press and are regulating the time and temperature. To replace the electronic devices switch off the heat press and pull the plug out from the wall outlet. The heating band must be cooled.
  • Page 12: Troubleshooting

    4.4 Troubleshooting Problem Cause Debugging main f use 10 A ist def ect Exchange main f use 10 A Green main switch button shines, but: if the main f use is okay, than the electronic dev ices are def ect display doesn´t glow Exchange electronic dev ices heat plate doesn´t f uel...
  • Page 13: Connection Diagram

    4.5 Connection diagram Version 15.01 13/14...
  • Page 14: Testing Report

    EN 292-1 EN 292-2 safety of machines EN 60204-1 electrical equipment of machines Berlin , .._____________________________ Peter Meidinger President All SCHULZE heat presses are exempt from the waste disposal law under reg. no. DE 231060054. Version 15.01 14/14...

Table of Contents