Advertisement
Quick Links
Advertisement
Related Manuals for Advantech B+B SmartWorx SmartStart
Summary of Contents for Advantech B+B SmartWorx SmartStart
- Page 1 Start Guide SmartStart, SmartFlex, SmartMotion...
-
Page 2: Safety Instructions
Start Guide Safety instructions Please take care to following instructions: Use the router in compliance with national and international law and in compliance with any special or additional restrictions regulating use of the router in the various applica- tions and environments. To avoid possible injury and/or damage to the device, observe the relevant provisions and standards. -
Page 3: Product Disposal Instructions
flash drive medium. If you are interested in obtaining the source, please contact us at: cellularsales@advantech-bb.com Modifications and debugging of LGPL-linked executables: The manufacturer of the device hereby grants the right to use debugging techniques (e.g. - Page 4 Start Guide QSG issued in CZ, January 25, 2017...
- Page 5 SmartStart SmartStart Router SL302, SL304 QSG issued in CZ, January 25, 2017...
-
Page 6: First Use
SmartStart First Use Before applying power to the router, connect the components that you required for your applications. You cannot operate the router without connected antenna, inserted SIM card, nor connected power supply. If you do not have connected main antenna during operation of the router, the router can be damaged! 1. - Page 7 SmartStart Before handling of the SIM card disconnect the router from power supply! 3. Power The router requires an external DC power supply. The DC voltage required is between +9 to +36 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router (see figure below).
- Page 8 SmartStart 4. Ethernet An Ethernet cable may be connected to the ETH connector (designated as ETH0 in some versions of this router) on the front panel (see figure above). By default, the Ethernet port is configured as follows: Connector Purpose Default Setting LAN port (default) DHCP Server...
- Page 9 SmartStart When the PWR LED starts blinking, it is possible to restore the default configuration of the router by pressing the RST button on the rear panel. After pressing this button, the default configuration is restored and then the router reboots (green LED will be on). After logging on to the device for the first time, we strongly recommend to change the default password due to security reasons.
- Page 10 SmartStart QSG issued in CZ, January 25, 2017...
- Page 11 SmartFlex SmartFlex Router SR300, SR303, SR305, SR306, SR307 QSG issued in CZ, January 25, 2017...
- Page 12 SmartFlex First Use Before applying power to the router, connect the components that you required for your applications. You cannot operate the router without connected antenna, inserted SIM card, nor connected power supply. If you do not have connected main antenna during operation of the router, the router can be damaged! SmartFlex SR300 routers are not equipped with a GSM module which means that SIM card readers and antenna connectors are not available on the router.
- Page 13 SmartFlex 2. SIM card The SIM card readers, for 3 V and 1.8 V SIM cards, are located on the rear panel of the router. If you intend to use this device to communicate over a cellular network, please place an activated data-provisioned SIM card with an unblocked PIN into the SIM card reader.
- Page 14 SmartFlex 4. Ethernet An Ethernet cable may be connected to the ETH0 connector on the front panel (see figure above). By default, this Ethernet port is configured as follows: Connector Purpose Default Setting ETH0 LAN port (default) DHCP Server Connect your laptop or PC to this port to IP Address: 192.168.1.1 get a local web-server for device configu- NetMask: 255.255.255.0...
- Page 15 SmartFlex 3. Restoring and Backing up the Router Configuration After you reset the router, the current configuration is overwritten by the default settings. We recommend that you back up the router configuration before resetting the device. Refer to the Configuration manual for more information. When the PWR LED starts blinking, it is possible to restore the default configuration of the router by pressing the RST button on the rear panel.
- Page 16 SmartFlex QSG issued in CZ, January 25, 2017...
- Page 17 SmartMotion SmartMotion Router ST352, ST355 QSG issued in CZ, January 25, 2017...
- Page 18 SmartMotion First Use Before applying power to the router, connect the components that you required for your applications. You cannot operate the router without connected antenna, inserted SIM card, nor connected power supply. If you do not have connected main antenna during operation of the router, the router can be damaged! 1.
- Page 19 SmartMotion Before handling of the SIM card disconnect the router from power supply! 3. Power The router requires an external DC power supply. The DC voltage required is between +10 to +60 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router (see figure below).
- Page 20 SmartMotion Configuration 1. Configuring the Device Using the Web Browser You can access the router for status monitoring, configuration, and administration after en- tering the IP address of the router into the web interface. The default IP address is 192.168.1.1 (netmask 255.255.255.0).