For Your Safety Read Before Lighting; Operation - Hargrove HARETHC24N2C Installation And Operation Manual

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which is lighted by a
spark
igniter system. When lighting the pilot, follow
these
instructions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
*Do not try to light any appliance.
*Do not touch any electric switch; do not use any
phone in your building.
* Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
*If you cannot reach your gas supplier, call the fire
department.
WARNING:
At no time should the "LIGHTING INSTRUCTION" tags be detached from
the burner system. Removing the tags will void the manufacturer's warranty.
1. STOP! Read the safety information above on this
label.
2. Turn off all electrical power in firebox before
installing.
3. Depress the control knob and turn clockwise
as far as it will go to reach the "OFF" position.
4. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor.
smell gas, STOP!
information above on this label.
smell gas, go to the next step.
5. Depress the
counterclockwise
Fig 10 GAS CONTROL
Control
Knob
Flame Height Control Knob
6. Push in control knob all the way and hold in.
* If the control knob is not held in all the way the pilot
will not stay lit when the knob is released.
* Do not turn the knob when pushing it in.
7. Light the pilot (mounted in front of the back burner)
by pushing the spark igniter button several times.
This will cause a spark at the pilot which will ignite
the pilot gas. If the spark does not work, light the
pilot with a match.
* When lighting the pilot it may take several seconds for
gas to reach the pilot.
8. Continue to hold the control knob in all the way for
about 30 seconds after the pilot is lit.
9. Release the knob and it will pop back out. The pilot
should remain lit. If it goes out, repeat steps 3 through
9.
* If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
* If the pilot will not stay lit after several tries, turn the

OPERATION

LIGHTING INSTRUCTIONS
Follow "B" in the safety
If you do not
control knob and
to the "PILOT" position.
Control Knob
WARNING:
instructions exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Force or attempt repair
may result in a fire or explosion and may void your
warranty.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
gas control knob to "OFF" and call your service
technician or gas supplier.
7. Depress the control knob and turn counterclockwise
to "ON".
counterclockwise to select desired comfort level.
IMPORTANT:
If you
device. After shutting off all gas flow, the pilot
burner cannot be relit until the thermocouple has
cooled, allowing the electromagnet to be released
(approx. 60 sec.).
turn
designed to be operated by hand. DO NOT use any
tools during this operation. Damaged knobs may
result in serious injury.
NOTE: A periodic visual check of the pilot flames
(Figure 11) and main burner flames (Figure 12) should
be made. The pilot flame should always be present
when the appliance is in operation. See illustrations
below.
NATURAL GAS
Fig 11
ODS PILOT
WARNING:
WILL VOID THE MANUFACTURER'S WARRANTY.
Fig 12
If you do not follow these
Turn flame
The gas control has an interlock
The gas control knob is
LIQUID PROPANE
ODS PILOT
TAMPERING WITH THE ODS PILOT
MAIN BURNER
heightl knob
16