Advertisement
2.2
Device Wiring (With Secure Door Control Unit
Face Recognition Terminal
Power Input
Sensor Input
Secure Door
Control Unit
Wiring Terminal
Exit Button
Lock Output
3
Activation
Power on and wire the network cable after installation. You should
activate the device before the first login.
If the device is not activated yet, it will enter the Activate Device page after powering on.
Steps:
1. Create a password and confirm the password.
2. Tap Activate to activate the device.
For other activation methods, see the device user manual.
5
Adding Face Information
1. Use finger to hold the screen surface and enter the activation password to
enter the main page.
2. Enter the User Management page, tap + to enter the Add User
page.
Only the devices with the fingerprint module support the fingerprint related functions.
4. Tap Face and collect the face information according to the
instructions.
You can view the captured picture at the upper right corner of
the page. Make sure the face picture is in good quality and size.
For details about the tips and positions when collecting or
comparing the face picture, see the contents on the right.
5. If the picture is in good condition, tap Save to save the picture.
Or tap Try Again to take another face picture.
6. Tap
to save the settings.
Go back to the initial page to start authentication.
For other authentication methods, see the device user manual.
Recommended:
Use other authentication methods if the device if affected by the light or other
items.
1:1 Matching: The device will compare the captured face picture with the ones
in the database.
1:N Matching: The device will compare the captured face picture with the user
linked face picture.
Biometric recognition products are not 100% applicable to anti-spoofing
environments. If you require a higher security level, use multiple authentica-
tion modes.
Secure Door Control Unit
Red
Black
Door Contact
Green/Brown
SENSOR
B1
Black
B2
The secure door control unit
Exit Button
should connect to an external
BUTTON
Green/Black
B3
power supply separately. The
Black
B4
suggested external power supply
is 12 V, 0.5 A.
White/Purple
NC
NC
C1
Electric
COM
White/Black
C2
Dropbolt
White/Red
NO
C3
Power
Electric
Strike
NO
STRONG PASSWORD RECOMMENDED–
We highly recommend you create a strong password of your
own choosing (using a minimum of 8 characters, including
upper case letters, lower case letters, numbers, and special
characters) in order to increase the security of your product.
And we recommend you reset your password regularly,
especially in the high security system, resetting the password
monthly or weekly can better protect your product.
Tips When Collecting/
Comparing Face Picture
Expression
Keep your expression naturally when collecting or comparing face pictures, just like the
expression in the picture on the right.
Do not wear hat, sunglasses, or other accessories that can
affect the facial recognition function.
Do not make your hair cover your eyes, ears, etc. and
heavy makeup is not allowed.
Posture
In order to get a good quality and accurate face picture, position your face looking at
the camera when collecting or comparing face pictures.
Correct
Tilt
Side
Size
Make sure your face is in the middle of the collecting window.
Correct
Too Close
Too Far
4
Two-way Audio
After adding the device to the client software, you can call the device from the client software, call the client
software from the device, call the center from the device, or call the indoor station form the device.
Call Client Software from Device
After adding the device on the client software, tap
->
on the client software to start two-way audio.
If the device is added by multiple client softwares and when the device is calling the client software, only
the first client software added the device will pop up the call receiving window.
Call Center from Device
After adding the device and center on the client software, tap
center answers the call, you can start two-way audio.
The device will call the center in priority when tap the administrator icon.
Call Device from Client Software
After adding the device on the client software, you can enter the Live View page. Right click the live
view window and click Start Two-Way Audio to start two-way audio.
Call Indoor Station from Device
After adding the device and the indoor station on the client software, link the added user and the
added indoor station, and set a room No. for the indoor station.
Tap
and enter the room No. And tap OK to call the indoor station.
Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m)
Recommended Height:
1.43m to 1.90m
1.4m
Raise
Bow
0.5m
Too
Too
Correct
Close
Far
Height:
1.4m
1.43m to 1.90m
1.4m
Move
Back and Forth
0.5m
0.5m
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
, and tap Answer on the pop-up window
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
->
to call the center. When the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Too High
regulations, fire prevention regulations and other related regulations in your local
region.
consumption cannot be less than the required value.
over-heat or fire hazard.
Too Low
dismantle the device.
the power cable, and then please contact the service center.
service center. Never attempt to disassemble the device yourself. (We shall not assume
any responsibility for problems caused by unauthorized repair or maintenance.)
1.4m
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
the detailed operating temperature), cold, dusty or damp locations, and do not expose
it to high electromagnetic radiation.
0.5m
heater or radiator is forbidden (ignorance can cause fire danger).
occur otherwise (which is not a malfunction however), and affecting the endurance of
Too Far
Too Close
sensor at the same time.
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
cover, do not use alkaline detergents.
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
1.4m
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.
ments. If you require a higher security level, use multiple authentication modes.
away from the light, and at least 3 meters away from the window or the door.
Power Source with 100~240 VAC or 12 VDC according to the IEC60950-1 standard.
1.2m
Please refer to technical specifications for detailed information.
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the RE Directive
2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recycle-
this.info
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info
Warnings
All the electronic operation should be strictly compliance with the electrical safety
Please use the power adapter, which is provided by normal company. The power
Do not connect several devices to one power adapter as adapter overload may cause
Please make sure that the power has been disconnected before you wire, install or
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
If the product does not work properly, please contact your dealer or the nearest
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
Do not place the device in extremely hot (refer to the specification of the device for
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as
Do not aim the device at the sun or extra bright places. A blooming or smear may
Please use the provided glove when open up the device cover, avoid direct contact
Please use a soft and dry cloth when clean inside and outside surfaces of the device
Please keep all wrappers after unpack them for future use. In case of any failure
Improper use or replacement of the battery may result in hazard of explosion.
Biometric recognition products are not 100% applicable to anti-spoofing environ-
Indoor use. If installing the device indoors, the device should be at least 2 meters
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited
Advertisement
