Table of Contents
Advertisement
6. Orient the Handlebar (47) as shown.
Tip: Avoid pinching the Pulse Wire (32).
Attach the Handlebar (47) to the Upright (3) with
two M8 x 18mm Screws (46).
7. The Console (6) can use four D batteries (not
included); alkaline batteries are recommended.
Do not use old and new batteries together or
alkaline, standard, and rechargeable batter-
ies together. IMPORTANT: If the Console has
been exposed to cold temperatures, allow
it to warm to room temperature before you
insert batteries. Otherwise, you may dam-
age the console displays or other electronic
components. Remove the screws (B) and the
battery covers (C), insert batteries into the bat-
tery compartments, and then reattach the battery
covers. Make sure to orient the batteries as
shown by the diagrams inside the battery
compartments.
To purchase an optional power adapter, call
the telephone number on the cover of this
manual. To avoid damaging the Console (6),
use only a manufacturer-supplied regulated
power adapter. Plug one end of the power
adapter into the receptacle (D) inside the indi-
cated battery compartment, and route the power
adapter through the notch (E) in the battery
cover. Then, plug the other end into an outlet
installed in accordance with all local codes and
ordinances.
6
47
32
46
7
6
D
10
3
C
E
B
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the PRO-FORM CYCLE TRAINER 400 Ri and is the answer not in the manual?
Questions and answers
Replace batteries
To replace batteries in the ICON PRO-FORM CYCLE TRAINER 400 Ri:
1. Ensure Proper Conditions: If the console has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries to prevent damage.
2. Remove Battery Covers: Use a screwdriver to remove the screws (B) and take off the battery covers (C).
3. Insert Batteries: Place new batteries into the battery compartments, ensuring they are oriented correctly as shown in the diagrams inside the compartments. Do not mix old and new batteries or different types (alkaline, standard, or rechargeable).
4. Reattach Battery Covers: Secure the battery covers back in place with the screws.
Alternatively, if using a power adapter, use only a manufacturer-supplied regulated power adapter and follow the instructions for connecting it properly.
This answer is automatically generated
my reed switch doesnt work, adjusted closer to the magnet and i will not pick up rpm.
To fix the Reed Switch issue on the ICON PRO-FORM CYCLE TRAINER 400 Ri that is not picking up RPM:
1. Locate the Reed Switch - Find the Reed Switch (21) near the Pulley (13).
2. Align the Pulley Magnet - Turn the Pulley until a Pulley Magnet (16) is aligned with the Reed Switch.
3. Adjust the Reed Switch - Slightly loosen the M4.5 x 12mm Flange Screws (63).
4. Reposition the Reed Switch - Move the Reed Switch slightly closer to or away from the Pulley Magnet.
5. Secure the Reed Switch - Retighten the Flange Screws.
6. Test the Adjustment - Turn the Pulley for a moment to check if the RPM is detected correctly.
If the issue persists, ensure the batteries are working and properly installed.
This answer is automatically generated
the pedal resistance is very high and doesn't chance with the app
The pedal resistance may be high and not changing with the app due to one of the following reasons:
1. Manual Override: If the resistance was manually adjusted using the Digital Resistance buttons, it may not change automatically with the app until the next workout segment begins.
2. Console Activation: The console may require activation. If it has not been activated, the resistance control may not function properly.
3. Low Batteries: If the console batteries are low, it may not respond correctly to resistance changes from the app.
4. Reed Switch Misalignment: If the console is not displaying correct feedback, the Reed Switch may need adjustment to ensure proper communication with the resistance mechanism.
To troubleshoot, check the console activation, replace the batteries if needed, and adjust the Reed Switch if the resistance is not responding correctly.
This answer is automatically generated