Pro ignition protected dc thruster models (32 pages)
Summary of Contents for SLEIPNER MOTOR AS SXP35
Page 1
Installation Guide For Pro DC External Electric Thruster Models SXP35, SXP50 DOCUMENT ID: SLEIPNER MOTOR AS 5926 REVISION: P.O. Box 519 DATE: N-1612 Fredrikstad 2023 Norway LANGUAGE: www.sleipnergroup.com...
If required by local regulation, electrical work must be done by a licensed professional. Appropriate health and safety procedures must be followed during installation. Faulty installation of Sleipner products will render all warranties given by Sleipner Motor AS. Ensure appropriate access to Sleipner products during installation planning for service, inspection and component replacement.
Page 4
Sleipner products. If you are interfacing the S-Link™ bus by agreement with Sleipner through a designated Sleipner supplied interface, you are still required to install at least one original Sleipner control panel to enable efficient troubleshooting if necessary. MC_0105 SXP35 & SXP50 5926 2023...
Height of support bolts from tube 35.8 Distance of support bolts from tube Distance of support bolts * Standard tube (Hull thickness <50mm) * Extended tube for thicker hull models (Hull thickness >50mm to <150mm) Water line MG_0110 SXP35 & SXP50 5926 2023...
Page 6
Product Measurements 187 mm 7’ 36” 170 mm 6’ 69” 121 mm 4’ 76” MG_0132 SXP35 & SXP50 5926 2023...
Metal hull, support or frame for mounting the SX thruster SX seawater resistant aluminium frame Galvanic isolation will prevent any current flow to the SX thruster Material to isolate the contact area of the MG_0565 surfaces fasteners SXP35 & SXP50 5926 2023...
Do not install the SX thruster inverted or at an angle over a reasonable level to deliver appropriate thrust Installing the thruster at an angle close to the water line will blast water beyond the water surface. MG_0109 SXP35 & SXP50 5926 2023...
Apply anti fouling to the gear leg and propeller. Do not apply anti fouling to any rubber elements of the gear leg or anodes if applicable. (NB: Ensure to paint under plastic covers.) WARNING Do not use abrasive tools damaging the existing Epoxy coating when preparing for antifouling paint. MG_0478 SXP35 & SXP50 5926 2023...
Ensure tunnel moulding around the gear leg and tunnel top align.) IMPORTANT Ensure all snap-lock positions are correctly connected into place. Ensure top lips tabs into the motor inserts. Push two tunnel ends together. Snap lock Check snap lock positions around the tunnel. MG_0112 SXP35 & SXP50 5926 2023...
50mm Spacer Compression ring Apply MS Polymer sealant or equal to back surface face Hull Compression Drill ring 8.5 / 9 mm 12mm Spacer MG_0262 SXP35 & SXP50 5926 2023...
Approximate the location of the control box. Nut and Washer All rings need +10% Compression Control box installation location Water line Hull thickness Maximum hull thickness SX thruster hose is 50 mm or 150mm MG_0113 SXP35 & SXP50 5926 2023...
Page 14
Insert the thruster with compression rings into the hole. Fasten the thruster Sealant (MS Polymer) Cover the entire surface Drill holes in hull SX surface area on the outer hull Thruster and attachment bolts Sealant (MS Polymer) MG_0504 SXP35 & SXP50 5926 2023...
Correct rotation of the grid/ cowl requires the longer spaced bolts at the top and the shorter spaced bolts at the bottom Tighten 2Nm WARNING Cowls are not used in combination with the hydropod MG_0145 SXP35 & SXP50 5926 2023...
Mark the locations of the four drill holes and drill the holes. Ensure that the back wall where the Control Box is to be mounted have suffi cient thickness and strength. Control box installation location Water line Hose claps SX thruster hose MG_0530 SXP35 & SXP50 5926 2023...
MC_0477 For PPC installation please refer to the Installation Guide accompanying the Proportional Power Pontroller. Installation Guide Proportional Power Controller SLEIPNER MOTOR AS DOCUMENT ID: P.O. Box 519 REVISION: DATE: N-1612 Fredrikstad Norway LANGUAGE: www.sleipnergroup.com SXP35 & SXP50 5926 2023...
For Control Panel installation please refer to the Installation Guide accompanying the control panel to be installed. Installation Guide Control Panel SLEIPNER MOTOR AS DOCUMENT ID: REVISION: P.O. Box 519 N-1612 Fredrikstad DATE: Norway www.sleipnergroup.com LANGUAGE: SXP35 & SXP50 5926 2023...
Correct drive direction as per control panel: ..............................The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for flooding: .................................................................................................................................. Other comments by installer: .................................................................................................................................................................... SXP35 & SXP50 5926 2023...
MC_0024 Sleipner Motor AS (The “Warrantor”) warrants that the equipment (parts, materials, and embedded software of products) manufactured by the Warrantor is free from defects in workmanship and materials for purpose for which the equipment is intended and under normal use and maintenance service (the “Warranty”).
Need help?
Do you have a question about the SXP35 and is the answer not in the manual?
Questions and answers