Toshiba HWT-602S21SM3W-E(TR) Service Manual page 165

DN
A4
Set temperature B' with outside temperature of T1
A5 Set temperature E' with outside temperature of 20°C
AB
Group control
AC
The temperature increase during
"Forced ON" mode (SG Ready control)
B2 HP restart water temperature in A zone. (Valid only
room temp control using 2nd remote controller)
B5 Initial water temperature setting method when
controlling heating by the room temperature remote
controller and room temperature thermostat
B6 Setting the objects to control of I/P 7, 8
B8 Forcibly heater off at T0 ≥ A°C
B9 Backup heater energization temperature during
defrosting.
680 0 - 10 V input setting
681 0 - 10 V Hot water supply temperature setting
682 0 - 10 V Heating ZONE1 temperature setting
683 0 - 10 V Heating ZONE2 temperature setting
684 0 - 10 V Cooling temperature setting
685 0 - 10 V Hot water supply temperature upper limit
686 0 - 10 V Heating ZONE1 temperature upper limit
687 0 - 10 V Heating ZONE2 temperature upper limit
688 0 - 10 V Cooling temperature upper limit
689 0 - 10 V Hot water supply temperature setting
resolution
68A 0 - 10 V Heating ZONE1 temperature setting resolution 0001: 1°C
68B 0 - 10 V Heating ZONE2 temperature setting resolution 0001: 1°C
68C 0 - 10 V Cooling temperature setting resolution
6A6 P1 pump speed control
6A7 Pump speed control correction
6AC Hot water supply mode operation cycle to prevent
water temperature drop
* DN_11, 6B8, 6BA, 6BC are needed for PCB replacement or DN code reset procedure has been completed.
Item Details
0020: 20°C - 0055: 55°C (401 / 601),
0065: 65°C (801 / 1101)
0020: 20°C - 0055: 55°C (401 / 601),
0065: 65°C (801 / 1101)
0000: TTW value of each Hydro Unit
0001: TTW value transmitted from Master Unit
0000: 0K - 0010: 10K
0020: 20°C - 0037: 37°C
0000: The fixed temperature by DN_9D
0001: The calculated temperature by Auto curve
0000: I/P 7 Emergency shutdown input, I/P 8 None
0001: I/P 7 TEMPO 1 input, I/P 8 None
0002: I/P 7 TEMPO 2 input, I/P 8 None
0003: I/P 7 Forcibly turn off the backup heater,
I/P 8 Forcibly turn off the hot water tank heater
0004: I/P 7 SG network input 1,
I/P 8 SG network input 2
0000: no restriction, 0001: 20°C
0002: 15°C, , 0006: -5°C
■■■
Correction coefficient B
0000: 0K, , 0004: 40K
■■■
0000: Not use
0001: Temperature setting
0002: Capacity setting of Heating / Cooling
0003: Capacity setting of Hot water supply
0004: Capacity setting of Heating / Cooling +
Hot water supply
0000: Not use AI 0001: AI 1
0002: AI 2 0003: AI 3
0000: Not use AI 0001: AI 1
0002: AI 2 0003: AI 3
0000: Not use AI 0001: AI 1
0002: AI 2 0003: AI 3
0000: Not use AI 0001: AI 1
0002: AI 2 0003: AI 3
0040: 40°C - 0080: 80°C
0020: 20°C - 0055: 55°C (401 / 601),
0065: 65°C (801 / 1101)
0020: 20°C - 0055: 55°C (401 / 601),
0065: 65°C (801 / 1101)
0007: 7°C - 0029: 29°C
0001: 1°C - 0005: 5°C
- 0005: 5°C
- 0005: 5°C
0001: 1°C - 0005: 5°C
0000: P1 pump fixed speed (depend on DN_A0
setting)
0001: P1 pump variable speed
0000: 100% 0001 :90%
0002: 75% 0003: 50%
0000: Invalid
0001: 1H - 0050: 50H
164
Factory default
0035: 35°C
0020: 20°C
0000: each Hydro Unit
0000: 0K
0025: 25°C
0000: The fixed
0000: I/P 7
Emergency
shutdown input,
I/P 8
None
0000: no restriction
0000: 0K
0000: Not use
0000: Not use AI
0000: Not use AI
0000: Not use AI
0000: Not use AI
0065: 65°C
0055: 55°C
0055: 55°C
0020: 20°C
0005: 5°C
0003: 3°C
0003: 3°C
0001: 1°C
0001: Variable speed
0000: 100%
0024: 24H