SIIG USB 2.0 4-Port Bay Hub Quick Installation Manual

SIIG USB 2.0 4-Port Bay Hub Quick Installation Manual

Advertisement

Quick Links

USB 2.0 4-Port Bay Hub
Quick Installation Guide

Introducing the USB 2.0 4-Port Bay Hub

The USB 2.0 4-Port Bay Hub is designed to support USB
2.0 equipped PC computers. This USB 2.0 hub expands
USB connectivity to your computer.
Features and Benefits
Compliant with USB Specifications, Revision 2.0
Drive bay design adds ports to the front of your
computer for convenient device connection
Fits into either 3.5" or 5.25" (with included mounting
rack) drive bay
Provides 4 downstream ports for USB device
connections
Supports high-speed (480Mbps), full-speed
(12Mbps), and low-speed (1.5Mbps) data transfer
modes
Per port over-current detection and protection
Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
Hot-swapping feature allows you to attach/detach
USB devices without powering your computer off
Note: USB 1.1 devices are limited to USB 1.1
speeds even when they are connected to a USB 2.0
host adapter or USB 2.0 hub.
04-0252B
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the USB 2.0 4-Port Bay Hub and is the answer not in the manual?

Questions and answers

Summary of Contents for SIIG USB 2.0 4-Port Bay Hub

  • Page 1 USB 2.0 4-Port Bay Hub Quick Installation Guide Introducing the USB 2.0 4-Port Bay Hub The USB 2.0 4-Port Bay Hub is designed to support USB 2.0 equipped PC computers. This USB 2.0 hub expands USB connectivity to your computer.
  • Page 2 One empty 3.5" or 5.25" drive bay • Windows 98 SE/ME/2000/XP/Server 2003 Package Contents • USB 2.0 4-Port Bay Hub • (1) "Y" split power cable • (1) USB 2.0 cable • (1) 5.25" mounting rack • (1) Bag assorted holding screws •...
  • Page 3 5.25" Mounting Rack Assembly Important: Use the Mounting Rack Assembly only when installing the hub into a 5.25" drive bay. Figure 2. 5.25" Mounting Rack Assembly USB Cable Connectors Type A connector Type B connector Figure 3. USB Cable Connectors...
  • Page 4 Installing the USB 2.0 4-Port Bay Hub Important: In order for the USB 2.0 4-Port Bay Hub to work properly, the driver of your existing USB 2.0 host adapter has to have support for USB 2.0 hubs. Turn OFF the power to your computer and all connected peripheral devices.
  • Page 5 Connect the Type B connector of USB cable into the upstream port (root port) of the USB 2.0 4-Port Bay Hub. Figure 5. Connecting the USB 2.0 Cable Carefully thread the two cables through the drive bay opening then push the hub assembly into the drive bay.
  • Page 6 11. When Windows boots up, the USB 2.0 4-Port Bay Hub automatically gets detected and installed. The hub is now ready for device connection. 12. Connect the Type A connector of your USB device(s) into any of the downstream ports on the USB 2.0 4-Port Bay Hub.
  • Page 7 The 5-year manufacturer warranty supplied with this product is offered by SIIG, Inc. If you should happen to encounter any problems with this product, please follow the procedures below.
  • Page 8 Fremont, CA 94538-3152 USB 2.0 4-Port Bay Hub is a trademark of SIIG, Inc. SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.

Table of Contents