Reading Out Information; Configuring Date, Time, Units Of Measurement, Contrast And Backlight - Daikin EHVH08SU26CB6W User Reference Manual

3 Configure the holiday mode settings (when you go away).
4 Activate the holiday mode.
Possible holiday mode settings (when you go away)
Setting
From and Until First and last day of your holiday.
Operation mode Operation mode used during your holiday.
Heating Set point used during your holiday when the unit
is operating in heating mode.
DHW Turn ON or OFF domestic hot water operation
during your holiday.
INFORMATION
You can only change the From and Until settings in the
End user level. For changing the other settings, you have
to switch to Adv. end user level.
To activate or deactivate the holiday mode
Prerequisite: You have configured the holiday.
1 Go to [2.1]: > Holiday > Holiday.
2 Do one of the following:
▪ To activate, select Yes and press
▪ To deactivate, select No and press
Usage example: You go away during the winter
If you are in the following situation:
▪ In 2 days, you go away for 2 weeks during the winter.
▪ You want to save energy, but prevent your house from freezing.
Then you can do the following:
Prerequisite: You switched the permission level to Advanced end
user.
1 Configure the holiday. Go to [2]:
the following settings:
Setting
Holiday mode
From
Until
Operation mode
Heating
2 Activate the holiday mode.
▪ Go to [2.1]: > Holiday > Holiday.
▪ Select Yes and press
Advantage:
▪ Before and after your holiday, your normal schedule will be used.
▪ During your holiday, you save energy and prevent your house
from freezing.
Usage example: You come home during your holiday
If you are in the following situation:
▪ You configured and activated the holiday mode (Away).
▪ During your holiday, you come home for a few hours and want to
use your normal schedule.
Then you can do the following:
1 Deactivate the holiday mode.
2 When you go away again, activate the holiday mode again.
EHVH04~16SU18+26CB6W
Daikin Altherma – Low temperature split
4P449981-1 – 2016.06
Description
.
.
> Holiday, and configure
Value
Away
2 February 2014
16 February 2014
Heating
12°C
.
Advantage:
You do NOT have to change your schedule or holiday configuration.
4.6.4

Reading out information

To read out information
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [6]: > Information.
Possible read-out information
In menu...
[6.1] Sensor information
[6.2] Energy metering
[6.3] Error handling
[6.4] User permission level
[6.5] Actuators
[6.6] Operation modes
[6.7] Running hours
[6.8] Version
4.6.5 Configuring date, time, units of
measurement, contrast and backlight
To configure time and date
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [1]: > Set time/date.
INFORMATION
Switch to Adv. end user to change daylight saving time and
12/24h notation.
To configure units of measurement
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.6]: > User settings > Unit of measurement.
Possible units of measurement settings
Setting
Decimal point
Temperature
Produced energy
Flow
To configure the contrast of the user interface
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.1.1]: > User settings > Display > Contrast.
4 Operation
You can read out...
Room, tank or DHW, outside,
and leaving water temperature.
(If applicable)
Produced energy, consumed
electricity, and consumed gas.
Error history and contact/
helpdesk number.
Current user permission level.
Status/mode of each actuator.
Example: Domestic hot water
pump ON/OFF.
Current operation mode.
Example: Defrost/oil return
mode.
Running hours of the system.
Version information about the
system.
Possible units of measurement
▪ Dot
▪ Comma
▪ °C
▪ °F
▪ kWh
▪ MBtu
▪ l/min
▪ GPM
User reference guide
15