Advertisement
Please read this manual carefully before using this radio.
high power channel
low power channel
battery level
scanning
channel lockout
unlocking
earphone
earphone volume
transmitting
receiving
alarm
volume
It is convenient for the user to search for calls from other channels. When"Side Key 2" in the software is programmed to the scanning function, long press key for two seconds to enter into the scanning mode, the transceiver will start to scan with the current channel; Operate it again to exit.
Long press key to lock buttons, operate it again to unlock.
Short press key switch to channel mode, the channel display on the screen flashes, Short press power key to display the current battery level. Press the PTT button or automatically exit after 5 seconds.
Long press key for two seconds to enter into the monitor mode, release it to exit.
This function can be voice activated so the user doesn't have to press the PTT key.
When "VOX level" in the software is selected, short press key twice to enter into the VOX mode, then short press key or key to turn on/off the VOX.
The purpose of the TOT is to prevent any single person from using a channel for an extended period of time. An alarm will sound if the transmission continues beyond the set time. Thetransceiver will stop transmission if this occurs. To stop the alarm, release the PTT key and the transceiver will return to standby.
The function can prevent interference from other transceivers using the same channel.
The transceiver has a high-low power selection, it can be programmed.
If there is no signal or operation, the radio will reduce its power consumption. The battery power-saving function activates when the channel is unoccupied or has not been in operation.
If the battery power falls to the predetermined value during transmission, the transceiver will give out a voice prompt, please charge in time.
It is a function setting which prevents the inter-channel interference.
The transceiver has 50 CTCSS and 208 DCS,also non-standard subaudio can be programmed!
When"Side Key 2" in the software is programmed to the alarm function, long press key for two seconds to enter into the alarm mode, the transceiver will start to alarm with the current channel; press the PTT button to exit.
GMRS | ||||
channel | TX | RX | Power | subaudio |
1 | 462.5625 | 462.5625 | High | 67.0 |
2 | 462.5875 | 462.5875 | High | 118.8 |
3 | 462.6125 | 462.6125 | High | 127.3 |
4 | 462.6375 | 462.6375 | High | 131.8 |
5 | 462.6625 | 462.6625 | High | 136.5 |
6 | 462.6875 | 462.6875 | High | 141.3 |
7 | 462.7125 | 462.7125 | High | 146.2 |
8 | 467.5625 | 467.5625 | Low | D243N |
9 | 467.5875 | 467.5875 | Low | D032N |
10 | 467.6125 | 467.6125 | Low | D047N |
11 | 467.6375 | 467.6375 | Low | D051N |
12 | 467.6625 | 467.6625 | Low | D053N |
13 | 467.6875 | 467.6875 | Low | D065N |
14 | 467.7125 | 467.7125 | Low | D116N |
15 | 462.5500 | 462.5500 | High | 123 |
16 | 462.5750 | 462.5750 | High | D743I |
17 | 462.6000 | 462.6000 | High | D332I |
18 | 462.6250 | 462.6250 | High | 127.3 |
19 | 462.6500 | 462.6500 | High | D243I |
20 | 462.6750 | 462.6750 | High | D606N |
21 | 462.7000 | 462.7000 | High | D731I |
22 | 462.7250 | 462.7250 | High | 136.5 |
23 | 467.5500 | 462.5500 | High | 136.5 |
24 | 467.5750 | 462.5750 | High | 136.5 |
25 | 467.6000 | 462.6000 | High | 136.5 |
26 | 467.6250 | 462.6250 | High | 136.5 |
27 | 467.6500 | 462.6500 | High | 136.5 |
28 | 467.6750 | 462.6750 | High | 136.5 |
29 | 467.7000 | 462.7000 | High | 136.5 |
30 | 467.7250 | 462.7250 | High | 136.5 |
SPECIFICATIONS | |
Frequency Range | GMRS |
Supply Power | DC3.7V |
Memory Channel Antenna Configuration | 30 Internal Antenna |
Work Mode | Co/Differ-frequency Simplex Communication |
Ground Method | Cathode |
working temperature range | -30°~+60° |
TRANSMITTER | |
Output Power | ≤3W |
Modulation Mode | FM(F3E) |
Max. Frequency Deviation | ≤5KHz |
Sparious Radiation | ≤7.5μW |
Preemphasis Character | Per Octave 6dB |
Emission Current | ≤1800mA |
RECEIVER | |
Sensitivity | 0.16μV(12dB SINAD) |
Audio Power | ≥300mW |
Audio Distortion | 5% |
Itermodulation Interference Resistance | ≥60dB |
Receiving Current | ≤300mA |
Standby Current | ≤20mA |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the RB19P that isn't answered in the manual? Leave your question here.