Table of Contents
Advertisement
Quick Links
USB 2.0 4-Port Bay Hub
Quick Installation Guide
Introducing the USB 2.0 4-Port Bay Hub
The USB 2.0 4-Port Bay Hub is designed to support USB
2.0 equipped PC computers. This USB 2.0 hub expands
USB connectivity to your computer.
Features and Benefits
•
Compliant with USB Specifications, Revision 2.0
•
Drive bay design adds ports to the front of your
computer for convenient device connection
•
Fits into either 3.5" or 5.25" (with included mounting
rack) drive bay
•
Provides 4 downstream ports for USB device
connections
•
Supports high-speed (480Mbps), full-speed
(12Mbps), and low-speed (1.5Mbps) data transfer
modes
•
Per port over-current detection and protection
•
Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
•
Hot-swapping feature allows you to attach/detach
USB devices without powering your computer off
Note: USB 1.1 devices are limited to USB 1.1
speeds even when they are connected to a USB 2.0
host adapter or USB 2.0 hub.
04-0252C
1
Advertisement
Table of Contents
Related Manuals for SIIG JU-H42B22-S2
Summary of Contents for SIIG JU-H42B22-S2
- Page 1 USB 2.0 4-Port Bay Hub Quick Installation Guide Introducing the USB 2.0 4-Port Bay Hub The USB 2.0 4-Port Bay Hub is designed to support USB 2.0 equipped PC computers. This USB 2.0 hub expands USB connectivity to your computer.
- Page 2 • Bag assorted holding screws • Quick installation guide Hub Layout Important: The bay hub is shown in white in this manual. However, it is available in either black or white depending on the model purchased. Downstream Ports Power Upstream Port...
- Page 3 5.25" Mounting Rack Assembly Important: Use the Mounting Rack Assembly only when installing the hub into a 5.25" drive bay. Figure 2. 5.25" Mounting Rack Assembly USB Cable Connectors Type A connector Type B connector Figure 3. USB Cable Connectors...
- Page 4 Installing the USB 2.0 4-Port Bay Hub Important: In order for the USB 2.0 4-Port Bay Hub to work properly, the driver of your existing USB 2.0 host adapter has to have support for USB 2.0 hubs. Turn OFF the power to your computer and all connected peripheral devices.
- Page 5 Figure 5. Connecting the USB 2.0 Cable Carefully thread the two cables through the drive bay opening then push the hub assembly into the drive bay. Align the hub's screw holes with the appropriate holes in the drive bay, then carefully attach the hub to the case using the included mounting screws.
- Page 6 11. When Windows boots up, the USB 2.0 4-Port Bay Hub automatically gets detected and installed. The hub is now ready for device connection. 12. Connect the Type A connector of your USB device(s) into any of the downstream ports on the USB 2.0 4-Port Bay Hub.
-
Page 7: Technical Support And Warranty
Step 1: Submit your RMA request. Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA. If the product is determined to be defective, an RMA number will be issued. SIIG RMA department can also be reached at (510) 413-5333. - Page 8 6078 Stewart Avenue Fremont, CA 94538-3152, USA USB 2.0 4-Port Bay Hub is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation. Other names used in this publication are for identification only and may be trademarks of their respective companies.
Need help?
Do you have a question about the JU-H42B22-S2 and is the answer not in the manual?
Questions and answers