1. Manuals
  2. Brands
  3. SIIG Manuals
  4. Computer Hardware
  5. JJ-EC2011-S1
  6. Quick installation manual

SIIG JJ-EC2011-S1 Quick Installation Manual

Cyberserial dual expresscard
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Introducing the CyberSerial ExpressCard
The CyberSerial Dual ExpressCard adds two high-speed
serial ports to an ExpressCard equipped computer.
Features and Benefits
•
Compatible with hi-speed modems, monitoring
equipment, serial networking and other serial
devices
•
Two DB9 RS232 ports with 16550 UART
•
Supports data rate of up to 115 Kbps
•
Built-in 16-byte FIFO buffers dramatically increase
data transmit/receive speed, especially under
Windows multitasking environment
System Requirements
•
Notebook or desktop computer with an available
ExpressCard slot
•
Windows 2000/XP/Server 2003
Package Contents
•
CyberSerial Dual ExpressCard
•
2-port DB9 Fan-out Cable
•
Driver CD
•
Quick Installation Guide
04-0414A
CyberSerial Dual
ExpressCard
Quick Installation Guide
1

Advertisement

Table of Contents
loading

Related Manuals for SIIG JJ-EC2011-S1

Summary of Contents for SIIG JJ-EC2011-S1

  • Page 1 CyberSerial Dual ExpressCard Quick Installation Guide Introducing the CyberSerial ExpressCard The CyberSerial Dual ExpressCard adds two high-speed serial ports to an ExpressCard equipped computer. Features and Benefits • Compatible with hi-speed modems, monitoring equipment, serial networking and other serial devices •...
  • Page 2 Layout Fan-out Cable Connector Figure 1: CyberSerial Dual ExpressCard 2-port DB9 Fan-out Cable Figure 2: 2-port DB9 Fan-out Cable Note: Connect 2S to the Fan-out Cable Connector of the CyberSerial Dual ExpressCard. See Figure 1 above for more information. ExpressCard Connector DB9 Serial Ports...

  • Page 3: Hardware Installation

    Hardware Installation General instructions for installing the ExpressCard are provided below. Since the design of notebook computers vary, refer to your system’s reference manual for further information, if needed. Insert the CyberSerial Dual ExpressCard into the ExpressCard slot of the computer with it's Express Card Connector facing the slot.

  • Page 4: Driver Installation

    Driver Installation This section provides information on how to install the CyberSerial Dual ExpressCard drivers. Windows 2000 At the Found New Hardware Wizard, click Next. Select Search for a suitable driver for my device (recommended), and click Next. Check Specify a location, uncheck the other boxes, then click Next.

  • Page 5: Changing Com Port Number

    Windows Server 2003 At the Found New Hardware Wizard, select No, not this time, then click Next. Select Install from a list or specific location (Advanced), then click Next. Insert the driver CD, check Include this location in the search, uncheck the other box, type in D:\2003, and click Next.

  • Page 6: Removing The Expresscard

    Click the down arrow that is next to the COM Port Number box, select a COM port that is not in use, then click OK. Close Device Manager to save the changes. Removing the ExpressCard Before ejecting the CyberSerial Dual ExpressCard from the ExpressCard slot, first use the Safely Remove Hardware utility to stop it.

  • Page 7: Technical Support And Warranty

    RMA number posted on the outside of the shipping carton. • You are responsible for the cost of shipping the product to SIIG at the following address: SIIG, Inc. 6078 Stewart Avenue...
  • Page 8 Fremont, CA 94538-3152 CyberSerial Dual ExpressCard is a trademark of SIIG, Inc. SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other names used in publication are for identification only and may be trademarks of their respective companies.

Table of Contents