Table of Contents
Advertisement
Quick Links
Introduction
The DP CyberParallel Dual PCIe adds 2 high-
speed parallel ports to PCI Express enabled
systems and supports EPP/ECP and SPP
(standard) parallel port modes.
Features and Benefits
•
PCI Express 1-lane (x1) I/O card works
with PCI Express slots with different lane
width
•
Two parallel ports support ECP, EPP PS2
and SPP modes and works with various
types of parallel devices
•
Supports various types of Windows
application software
04-0964A
DP CyberParallel
Dual PCIe
Installation Guide
- based
®
1
Advertisement
Table of Contents
Related Manuals for SIIG JJ-E02211-S1
Summary of Contents for SIIG JJ-E02211-S1
- Page 1 DP CyberParallel Dual PCIe Installation Guide Introduction The DP CyberParallel Dual PCIe adds 2 high- speed parallel ports to PCI Express enabled systems and supports EPP/ECP and SPP (standard) parallel port modes. Features and Benefits • PCI Express 1-lane (x1) I/O card works with PCI Express slots with different lane width •...
-
Page 2: System Requirements
System Requirements • PCI Express enabled system with an available PCI Express slot • Windows 8 (32-/64-bit) / 7 (32-/64-bit) / ® Vista (32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / Server 2008 R2 / 2000 Package Contents •... - Page 3 Layout Stripe Parallel Port 2 (P2)* pin 1 Parallel Port 1 (P1) Figure 1 *Note: When connecting the DB25 ribbon cable to Parallel Port 2 (P2), position the ribbon cable so the stripe is on the side nearest to the slot bracket, see Figure 1.
-
Page 4: Hardware Installation
Hardware Installation Note: For low profile systems, replace the currently mounted bracket with the included low profile bracket. General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer's reference manual for further information, if needed. -
Page 5: Software Installation
If you need the second parallel port, connect the DB25 connector bracket now and remove another slot bracket cover from an available PCIe slot. Skip this step if you need only one parallel port. Carefully align the card to the selected PCIe slot, push the board down firmly, but gently, until it is well seated. - Page 6 Windows 8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-/64-bit) / Server 2008 (32-/64-bit) / Server 2008 R2 Insert the driver CD. Close the CD autoplay box if prompted. Check in Device Manager. For Windows 8 / 7: Right click Computer, click Manage, then click Device Manager.
- Page 7 For 64-bit / 2008 R2: Type D:\64bit, click Next. (Change D: to match your CD-ROM drive letter) At Windows has successfully updated your driver software, click Close. Go back to Device Manager, right click PCI Parallel Port, then click Update Driver Software.
- Page 8 For 32-bit: Type D:\32bit, click Next. (Change D: to match your CD-ROM drive letter) For 64-bit: Type D:\64bit, click Next. Change D: to match your CD-ROM drive letter) At Completing the Hardware Update Wizard, click Finish. Go back to Device Manager, right click PCI Parallel Port.
- Page 9 Type D:\32-bit, click OK, then click Next (Change D: to match your CD-ROM drive letter) At Completing the Found New Hardware Wizard, click Finish, then restart the computer to complete the installation. To Verify Windows Installation Check in Device Manager to verify installation.
- Page 10 Changing Parallel Port Some parallel port devices need a specific LPT in order to function properly. If your device works, do not make any changes. For Windows 8 / 7 / XP / 2003 / 2000: Right click Computer or My Computer, click Manage, then click Device Manager.
-
Page 11: Technical Support And Warranty
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued. - Page 12 Fremont, CA 94538-3152, USA Phone: 510-657-8688 DP CyberParallel Dual PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names used in this publication are for identification only and may be trademarks of their respective owners.