Page 1
GB100MG User Manual GPS Tracker TRACGB100MGUM001 Version: 1.00...
Page 2
TRACGB100MGUM001 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers. Queclink has not undertaken any independent search for additional relevant information, including any information that may be in the customer’s possession.
GB100MG User Manual Contents Contents ............................2 Table Index ............................3 Figure Index ............................4 0. Revision History ..........................5 1. Introduction ..........................6 1.1. Reference..........................6 2. Product Overview .......................... 7 2.1. Check Parts List ........................7 2.2. Parts List ..........................8 2.3.
Page 4
GB100MG User Manual Table Index Table 1. GB100MG Protocol Reference ..................... 6 Table 2. Parts List ..........................8 Table 3. Description of 2-Pin Power Cable ..................8 Table 4. Definition of Device Status and LED ................... 13 TRACGB100MGUM001 - 3 -...
Page 5
Figure 3. Close the Case ........................10 Figure 4. Install a SIM Card ......................11 Figure 5. Typical Power Connection ....................12 Figure 6. GB100MG LED on the Case ....................13 Figure 7. Motion Sensor Direction ....................14 TRACGB100MGUM001 - 4 -...
Bluetooth can be used for data transmission. It’s multiband LTE Cat-M1 and Cat-NB1 allow the GB100MG location to be monitored in real time or periodically tracked by a backend server and mobile devices. It’s built-in 3-axis accelerometer allows motion detection, 100Hz pre/post incident data collection, and extends battery life through sophisticated power management algorithms.
GB100MG User Manual 2. Product Overview 2.1. Check Parts List Before starting, check all the following items have been included with your GB100MG. If anything is missing, please contact your supplier. Figure 1. Appearance of GB100MG TRACGB100MGUM001 - 7 -...
2.2. Parts List Table 2. Parts List Name Picture GB100MG Locator 2.3. Interface Definition The GB100MG has a 2-pin power cable. The definition of the 2-pin power cable is shown below. Table 3. Description of 2-Pin Power Cable Index Colour Definition Description...
GB100MG User Manual 3. Getting Started 3.1. Open the Case Remove 6pcs screws from the device, insert the triangular-pry-opener into the gap of the case and push the opener up until the case is unsnapped. Figure 2. Open the Case...
GB100MG User Manual 3.2. Close the Case Step_1: Put the motherboard into the front case, and make sure the silicon rubber seal ring is in the gap of the front case and the power cable wire holder in the rubber groove of the rear case..
GB100MG User Manual 3.3. Install a SIM Card Step_1: Open the case and pull out the battery connector from the socket to ensure the device is not powered. Step_2: Slide the holder to the left to open the SIM card holder.
1. Do not connect any external cable on the GB100MG device. 2. The GB100MG simply mounts directly onto the vehicle’s battery with only two wires to attach. It should be installed and operated with a minimum distance of 20cm from human body.
Flashing pattern 5: 100ms On, 500ms Off, 100ms On, 2s not inserted and GNSS location not Off, 100ms On, 500ms Off, 100ms On, 500ms Off, 100ms fixed On, 2s Off Device power off or sleep mode Figure 6. GB100MG LED on the Case TRACGB100MGUM001 - 13 -...
GB100MG User Manual 3.6. Motion Sensor Direction GB100MG has an internal 3-axis accelerometer supporting driving behaviour monitoring and motion detection. The following shows the directions of the motion sensor. The Z axis faces outwards vertically. Figure 7. Motion Sensor Direction 4.
GB100MG User Manual 5. Certification 5.1. FCC Certification The product contains a LTE module FCC ID: XMR201707BG96 FCC Compliance Statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.