Related Manuals for Queclink GB100CAU
Summary of Contents for Queclink GB100CAU
- Page 1 GV50MG User Manual GB100CAU User Manual EGPRS /GPRS/WCDMA/LTE Cat 1/GNSS Tracker QSZTRACGB100CAUUM0100 Version: 1.00...
- Page 2 QSZTRACGB100CAUUM0100 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers. Queclink has not undertaken any independent search for additional relevant information, including any information that may be in the customer’s possession.
-
Page 3: Table Of Contents
GB100CAU User Manual Contents 0. Revision History ..........................1 1. Introduction ..........................2 1.1. GB100CAU Products ......................2 1.2. Reference..........................2 2. Product Overview .......................... 3 2.1. Product Appearance ......................3 2.2. LED Description ........................3 2.3. Parts List ..........................3 3. -
Page 4: Revision History
GB100CAU User Manual 0. Revision History Version Date Author Description of Change 1.00 2020-06-03 Eddy Qi Initial QSZTRACGB100CAUUM0100... -
Page 5: Introduction
GB100CAU User Manual 1. Introduction The GB100CAU is a device designed for self-installation by the customer. It is a telematics device based on LTE CAT1/WCDMA/EGPRS supporting Bluetooth. Its built-in accelerometer allows motion detection, incident detection, 100/200/400Hz pre/post incident data collection and extends battery life through sophisticated power management algorithms. -
Page 6: Product Overview
GB100CAU User Manual 2. Product Overview 2.1. Product Appearance Figure 1. Appearance of GB100CAU 2.2. LED Description Table 3. GB100CAU LED Description Device Status LED Status PWR LED The internal battery of device is in charge Fast flashing The internal battery of device is full... -
Page 7: Interface Definition
GB100CAU User Manual 3. Interface Definition The GB100CAU has a 2-pin power cable. The pin definition of the 2-pin power cable is as below: Table 4. Description of 2-pin Power Cable Cable Colour Definition Comment External DC power input, 8-32V... -
Page 8: Getting Started
GB100CAU User Manual 4. Getting Started 4.1. Opening the Case Insert the triangular-pry-opener into the gap of the case as shown below, push the opener up until the case unsnapped. Figure 2. Opening the Case 4.2. Closing the Case Make sure the silicon rubber seal ring is in the gap of front case. -
Page 9: Installing Sim Card
PWR (pin 1)/GND (pin2) are the power input pins. The input voltage range for this device is from 8V to 32V. The device is designed to be installed in vehicles that operate on 12V/24V without the need of external transformers. Note: Do not connect any external cables to GB100CAU device. QSZTRACGB100CAUUM0100... -
Page 10: Installation Precautions
GB100CAU User Manual 5. Installation Precautions Firmly install the device to a reliable surface to prevent falling off. Make the side with antenna face sky to have better signal reception. Do not install the device under metal surface or in enclosed environments having difficulty in getting GPS and network signal. -
Page 11: Troubleshooting And Safety Info
GB100CAU User Manual 6. Troubleshooting and Safety Info 6.1. Troubleshooting Problem Possible Reason Solution After the device is turned The signal is too weak. The Move the device to a place with on, the CEL LED always device isn’t registered to the good network coverage. - Page 12 FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.