Table of Contents
Advertisement
Instructions for cutting crown molding angled
between the fence and base of the saw for all cuts
Angle the molding so the bottom of the molding (part
u
which goes against the wall when installed) is against the
fence (11) and the top of the molding is resting on the saw
table (10), as shown in figure O1.
The angled "flats" on the back of the molding must rest
u
squarely on the fence and saw table.
Inside Corner
Left Side
Miter right at 45°
Save right side of cut
Right Side
Miter left at 45°
Save left side of cut
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Fig. Q, Q1
Bowed material (
When cutting bowed material always position it as shown in
figure Q1 and never like that shown in figure Q. Positioning
the material incorrectly will cause it to pinch the blade near
the completion of the cut.
Cutting round material
Rounded material should be clamped or held firmly to the
fence to keep It from rolling. This is extremely important when
making angle cuts.
Cutting large material
Occasionally you will encounter a piece of wood a little too
large to fit beneath the lower guard.
To clear the guard over the wood, with the saw off and your
right hand on the operating handle, place your right thumb
outside of the upper portion of the guard and roll the guard up
just enough to clear the wood, as shown in figure P. Release
the guard prior to starting the motor. The guard mechanism
will function properly during the cut. Only do this when neces-
sary.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Warning! Always be sure that the tool is switched off and
unplugged before adjusting or checking the tools function.
After use
After use, wipe off chips and dust adhering to the tool with
u
a cloth or the like.
Keep the blade guard clean according to the directions in
u
the previously covered section.
Lubricate the sliding portions with machine oil to prevent
u
rust.
Outside Corner
Miter left at 45°
Save right side of cut
Miter right at 45°
Save left side of cut
)
(Original instructions)
Carrying the tool
Make sure the tool is unplugged
u
Secure the blade at 0 bevel angle and 0 mitre angle.
u
Lower the handle fully and lock down by turning and
u
engaging the head locking pin (16).
Carry the tool with both hands holding the the tool base.
u
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (16) is for carrying and storage
u
purposes only and not for any cutting operations..
Troubleshooting
Problem
Possible Cause
Motor does
Saw not plugged in.
not start
Mitre table
unlocked.
Angle of cut
inaccurate
Too much sawdust
under table.
Parts Failure.
Pivot spring not
Cutting arm
replaced properly
cannot fully
after service.
raise, or blade
guard cannot
Sawdust build up.
fully close
Saw head locking
pin not set properly.
Saw blade
damaged.
Blade binds,
Dull blade.
jams or
shakes
Improper blade.
Warped blade.
Saw blade
damaged.
Saw blade
loosened.
Saw vibrates
or shakes
Saw not properly
fastened down.
Work piece not
properly supported.
Z
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
Speed
Blade outer diameter
ENGLISH
Solution
Check that all cords are plugged in.
Use mitre table locking lever (see
Adjusting the mitre angle section.
Vacuum or blow out dust. Wear eye
protection.
Contact service centre.
Contact service centre.
Clean and lubricate moving parts.
Check, adjust, and properly set saw
head locking pin.
Replace blade.
Replace or sharpen blade.
Replace blade.
Replace blade.
Replace blade.
Tighten arbor bolt.
Fasten saw to bench, stand or table.
Properly support or clamp work
piece.
BES702
V
230V
/min
4800
mm
216
15
Advertisement
Table of Contents
